| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B00D212 | Restraint System Malfunction Indicator 1 Circuit Short to Battery | One of the following conditions is met:
·
The airbag ECU assembly detects a short circuit +B signal in the passenger airbag ON/OFF indicator "ON" circuit when the airbag ECU assembly sends an "ON" request signal to the "ON" indicator in the passenger airbag ON/OFF indicator. ·
A telltale light assembly(passenger airbag ON/OFF indicator) malfunction. ·
An airbag ECU assembly malfunction. |
·
Wire harness ·
Telltale light assembly (passenger airbag ON/OFF indicator) ·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
To perform the simulation method, shake each connector of the airbag system or drive the vehicle on various types of road.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Turn the ignitino switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the airbag ECU assembly and telltale light assembly (passenger airbag ON/OFF indicator).
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the telltale light assembly(passenger airbag ON/OFF indicator) connector.
Procedure1
Check that the connectors (on the airbag ECU assembly side and telltale light assembly (passenger airbag ON/OFF indicator) side) are not damaged.
The terminals of the connectors are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D10,D38)Location & Routingewd_type=routing;type=c,c;code=D10,D38 Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assemblyewd_type=component;type=c;code=D10;pinno=35 Click Connector(D38)Instrument Panel>Instrument Panel Wire>Telltale Light Assemblyewd_type=component;type=c;code=D38;pinno=1 |
||
| D10-35 (PAON) or D38-1 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
OK
NG
Pre-procedure1
| *1 | Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
Connect the D38 telltale light assembly (passenger airbag ON/OFF indicator) connector.
Using a service wire, connect terminal 35 (PAON) of connector B and body ground.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Procedure1
Check the passenger airbag ON/OFF indicator operation.
The passenger airbag ON/OFF indicator "ON" does not come on.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Disconnect the service wire from connector B.
OK
NG