Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00D512  Restraint System Passenger Disable Indicator Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B00D512 Restraint System Passenger Disable Indicator Circuit Short to Battery One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit +B signal in the passenger airbag ON/OFF indicator "ON" circuit when the airbag ECU assembly sends an "ON" request signal to the "ON" indicator in the passenger airbag ON/OFF indicator.

·

A telltale light assembly (passenger airbag ON/OFF indicator) malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Telltale light assembly (passenger airbag ON/OFF indicator)

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C414742E11
5.49,0.844 6.104,1.042 0.615,0.198 10 false PAON 1.5,0.844 2.115,1.042 0.615,0.198 10 false PAON 0.615,0.594 1.229,0.792 0.615,0.198 10 false +B 5.229,0.844 5.844,1.042 0.615,0.198 10 false 35 2.031,0.833 2.646,1.031 0.615,0.198 10 false 1 0.052,2.052 2.781,2.677 2.729,0.625 10 false Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) 0.042,1.896 0.656,2.094 0.615,0.198 10 false D38 5.458,1.906 6.073,2.104 0.615,0.198 10 false D10 5.479,2.073 7.094,2.354 1.615,0.281 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, shake each connector of the airbag system or drive the vehicle on various types of road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and telltale light assembly (passenger airbag ON/OFF indicator).

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C215710C06
0.625,1.427 0.938,1.583 0.313,0.156 10 *1 2.531,1.563 2.844,1.719 0.313,0.156 10 *2 1.49,1.104 1.802,1.26 0.313,0.156 10 *3
*1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the telltale light assembly (passenger airbag ON/OFF indicator) connector.


Procedure1

a.

Check that the connectors (on the airbag ECU assembly side and telltale light assembly (passenger airbag ON/OFF indicator) side) are not damaged.

OK:

The terminals of the connectors are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
E459540C02
0.823,3.635 1.24,3.885 0.417,0.25 0.969,0.719 1.385,0.969 0.417,0.25 2.094,4.125 2.208,4.458 2.208,4.458 2.458,4.458 true 1.635,0.75 1.396,0.5 1.396,0.5 1.146,0.5 true 0.438,2.594 0.75,2.75 0.313,0.156 10 false *1 2.792,2.698 3.104,2.854 0.313,0.156 10 false *2 1.521,2.302 1.833,2.458 0.313,0.156 10 false *3 0.76,0.094 1.073,0.25 0.313,0.156 10 false *a 0.531,3.052 0.844,3.208 0.313,0.156 10 false *b 2.521,4.365 2.969,4.573 0.448,0.208 10 false PAON 0.917,3.677 1.427,3.958 0.51,0.281 10 false D10 0.74,0.417 1.25,0.698 0.51,0.281 10 false PAON 1.073,0.771 1.583,1.052 0.51,0.281 10 false D38 0.719,2.115 0.917,2.323 0.198,0.208 10 false D 0.969,2.115 1.167,2.323 0.198,0.208 10 false C 2.375,2.104 2.573,2.313 0.198,0.208 10 false A 2.125,2.115 2.323,2.323 0.198,0.208 10 false B
*1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Telltale Light Assembly (Passenger Airbag ON/OFF Indicator))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D10,D38)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

Click Connector(D38)Instrument Panel>Instrument Panel Wire>Telltale Light Assembly

D10-35 (PAON) or D38-1 (PAON) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

Pre-procedure1

a.
C414932C04
0.823,0.833 1.198,1.042 0.375,0.208 1.688,1.688 1.885,1.688 1.885,1.688 2.01,1.323 false 0.531,2.813 0.844,2.969 0.313,0.156 10 false *1 2.677,2.927 2.99,3.083 0.313,0.156 10 false *2 1.448,2.552 1.76,2.708 0.313,0.156 10 false *3 0.75,0.469 1.063,0.625 0.313,0.156 10 false *a 2.323,2.323 2.635,2.479 0.313,0.156 10 false A 2.042,2.313 2.354,2.469 0.313,0.156 10 false B 0.979,2.313 1.292,2.469 0.313,0.156 10 false C 0.833,2.302 1.146,2.458 0.313,0.156 10 false D 1.26,1.625 1.875,1.802 0.615,0.177 10 false PAON 0.865,0.854 1.479,1.031 0.615,0.177 10 false D10
*1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the D38 telltale light assembly (passenger airbag ON/OFF indicator) connector.


b.

Using a service wire, connect terminal 35 (PAON) of connector B and body ground.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


Procedure1

a.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator "ON" does not come on.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect the service wire from connector B.



OK

NG