Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00DF12  Passenger Restraints Disable Switch Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B00DF12 Passenger Restraints Disable Switch Circuit Short to Battery One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal and short circuit to B+ signal in the airbag cutoff switch cylinder sub-assembly circuit for 2 seconds.

·

An airbag cutoff switch cylinder sub-assembly malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Airbag cutoff switch cylinder sub-assembly

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C262371E29
2.094,1.063 2.573,1.26 0.479,0.198 10 false PMC+ 2.125,2.24 2.604,2.438 0.479,0.198 10 false PMC- 5.469,3.063 5.813,3.26 0.344,0.198 10 false D10 0.188,3.198 3.01,3.406 2.823,0.208 10 false Airbag Cutoff Switch Cylinder Sub-assembly 2.573,1.073 2.813,1.281 0.24,0.208 10 false 2 2.573,2.24 2.813,2.448 0.24,0.208 10 false 1 5.51,1.063 5.76,1.271 0.25,0.208 10 false 22 5.542,2.24 5.802,2.448 0.26,0.208 10 false 21 5.771,1.146 6.302,1.344 0.531,0.198 10 false MSW+ 5.771,2.344 6.302,2.542 0.531,0.198 10 false MSW- 0.167,3.042 0.531,3.229 0.365,0.188 10 false D47 5.469,3.208 7.052,3.698 1.583,0.49 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, shake each connector of the airbag system or drive the vehicle on various types of road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and airbag cutoff switch cylinder sub-assembly.


Result:
Result Proceed to
The connectors are properly connected A
The connectors are not properly connected B


Post-procedure1

a.

None



A

2.CHECK CONNECTORS

B

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C215710C06
0.625,1.427 0.938,1.583 0.313,0.156 10 *1 2.531,1.563 2.844,1.719 0.313,0.156 10 *2 1.49,1.104 1.802,1.26 0.313,0.156 10 *3
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the airbag cutoff switch cylinder sub-assembly connector.


Procedure1

a.

Check that the connectors (on the airbag ECU assembly side and airbag cutoff switch cylinder sub-assembly side) are not damaged.


Result:
Result Proceed to
The connectors are not deformed or damaged A
The connectors are deformed or damaged B


Post-procedure1

a.

None



A

3.CHECK HARNESS AND CONNECTOR

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
C414928C07
0.5,0.583 0.979,0.833 0.479,0.25 0.719,3.802 1.198,4.052 0.479,0.25 0.896,1.417 1.146,1.417 1.146,1.417 1.365,1.156 true 1.667,1.167 1.896,1.417 1.896,1.417 2.146,1.417 true 1.698,4.021 2.042,4.479 2.042,4.479 2.292,4.479 true 1.083,4.479 1.333,4.479 1.333,4.479 1.615,4.021 true 0.438,2.594 0.75,2.75 0.313,0.156 10 false *1 2.813,2.698 3.125,2.854 0.313,0.156 10 false *2 1.5,2.313 1.813,2.469 0.313,0.156 10 false *3 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.531,3.125 0.844,3.281 0.313,0.156 10 false *b 0.625,4.396 1.125,4.604 0.5,0.208 10 false MSW- 2.365,4.375 2.875,4.656 0.51,0.281 10 false MSW+ 0.844,3.844 1.354,4.125 0.51,0.281 10 false D10 2.229,1.344 2.74,1.625 0.51,0.281 10 false PMC+ 0.5,1.323 1.01,1.604 0.51,0.281 10 false PMC- 0.594,0.625 1.104,0.906 0.51,0.281 10 false D47 0.698,2.104 0.896,2.313 0.198,0.208 10 false D 1.01,2.104 1.208,2.313 0.198,0.208 10 false C 2.385,2.115 2.583,2.323 0.198,0.208 10 false A 2.063,2.115 2.26,2.323 0.198,0.208 10 false B
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder Sub-assembly)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D47)Location & Routing

Click Connector(D47)Instrument Panel>Instrument Panel Wire>Airbag Cut Off Switch Cylinder Sub-Assembly

D47-2 (PMC+) - Body ground Ignition switch ON Below 1 V
D47-1 (PMC-) - Body ground Ignition switch ON Below 1 V



Post-procedure1

Result:
Proceed to
OK
NG


a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.
C414930C01
0.792,1.479 1.104,1.677 0.313,0.198 10 false *1 2.708,1.625 3.021,1.823 0.313,0.198 10 false *2 1.729,1.177 2.042,1.375 0.313,0.198 10 false *3
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Reconnect the airbag ECU assembly connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC
5.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B00DF12 is output A
B00DF13 is output B


Post-procedure1

a.

None



A

B

REPLACE AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY