Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B005200  Passenger Seat Belt Sensor Circuit Undetermined Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B005200 Passenger Seat Belt Sensor Circuit Undetermined Failure When it is determined that the specified number of times or more is not achieved after the ignition switch is turned to ON.
·

Harness or connector

·

Front seat inner belt assembly RH (for LHD)

·

Front seat inner belt assembly RH (for RHD)

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

for LHD:
C253566E83
2.448,1.26 2.698,1.49 0.25,0.229 10 false 3 2.469,2.833 2.594,3.01 0.125,0.177 10 false 2 1.99,1.219 2.406,1.375 0.417,0.156 10 false RBE+ 2.031,2.792 2.427,2.938 0.396,0.146 10 false RBE- 5.833,1.365 6.323,1.563 0.49,0.198 10 false RBE+ 5.563,1.24 5.813,1.406 0.25,0.167 10 false 27 0.302,3.979 0.656,4.125 0.354,0.146 10 false G27 0.302,4.167 2.552,4.344 2.25,0.177 10 false Front seat Inner Belt Assembly RH 5.563,3.927 5.906,4.083 0.344,0.156 10 false G64 5.563,4.104 6.99,4.354 1.427,0.25 10 false Airbag ECU Assembly 5.583,2.823 5.833,2.99 0.25,0.167 10 false 18 5.833,2.927 6.354,3.115 0.521,0.188 10 false GNDR

for RHD:
C253566E84
2.448,1.229 2.698,1.458 0.25,0.229 10 false 3 2.469,2.802 2.594,2.979 0.125,0.177 10 false 2 1.938,1.219 2.354,1.375 0.417,0.156 10 false LBE+ 2.01,2.792 2.438,2.948 0.427,0.156 10 false LBE- 5.844,1.375 6.25,1.542 0.406,0.167 10 false LBE+ 5.563,1.24 5.813,1.406 0.25,0.167 10 false 30 0.302,3.979 0.656,4.125 0.354,0.146 10 false G25 0.302,4.167 2.552,4.344 2.25,0.177 10 false Front seat Inner Belt Assembly LH 5.563,3.927 5.906,4.083 0.344,0.156 10 false G43 5.563,4.104 6.99,4.354 1.427,0.25 10 false Airbag ECU Assembly 5.573,2.833 5.823,3 0.25,0.167 10 false 24 5.833,2.927 6.375,3.115 0.542,0.188 10 false GNDL

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK CONNECTION OF CONNECTORS

B

10.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and front seat inner belt assembly RH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C208245C65
0.646,1.75 0.958,1.948 0.313,0.198 10 false *1 2.573,1.542 2.885,1.74 0.313,0.198 10 false *2 1.5,1.427 1.813,1.625 0.313,0.198 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the front seat inner belt assembly RH connector.


Procedure1

a.

Check that the connectors (on the airbag ECU assembly side and front seat inner belt assembly RH side) are not damaged.

OK:

The terminals of the connectors are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

Pre-procedure1

a.

Remove the front seat inner belt assembly RH.

HINT:

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL



Procedure1

a.

Inspect the front seat inner belt assembly RH.

E459553C01
6.125,1.5 6.292,1.5 6.292,1.5 6.5,1.26 false 5.552,0.844 5.719,0.844 5.719,0.844 5.719,0.604 false 2.844,1.458 3.177,1.125 3.177,1.125 3.344,1.125 false 1.24,1.167 1.052,1.167 1.052,1.167 0.792,1.542 true 3.406,1.042 3.573,1.208 0.167,0.167 10 false *1 5.948,1.427 6.198,1.594 0.25,0.167 10 false *2 0.125,1.146 0.375,1.313 0.25,0.167 10 false *a 5.396,0.792 5.646,0.958 0.25,0.167 10 false *b 1.333,1.094 1.75,1.26 0.417,0.167 10 false RBE-
*1 Front Seat Inner Belt Assembly RH *2 Battery
*a Component without harness connected
(Front Seat Inner Belt Assembly RH)
*b Tester


Standard Current:
Tester Connection Condition Specified Condition
Tester positive (+) - 2 (RBE-)
Tester negative (-) - Battery negative (-)
Seat belt fastened 12.0 to 18.0 mA
Tester positive (+) - 2 (RBE-)
Tester negative (-) - Battery negative (-)
Seat belt not fastened 4.0 to 7.0 mA



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)
a.
E459554C01
0.427,0.74 0.844,0.99 0.417,0.25 1.167,3.823 1.583,4.073 0.417,0.25 1.125,0.25 1.292,0.25 1.292,0.25 1.469,0.708 true 1.5,3.5 1.583,3.5 1.583,3.5 1.906,3.896 true 1.479,4.427 1.646,4.427 1.646,4.427 2.021,4.156 true 2.021,0.271 1.854,0.271 1.854,0.271 1.667,0.698 true 0.385,2.927 0.573,3.094 0.188,0.167 10 false *1 0.708,2.427 0.896,2.594 0.188,0.167 10 false D 1.125,2.438 1.313,2.604 0.188,0.167 10 false C 1.938,2.427 2.125,2.594 0.188,0.167 10 false B 2.365,2.427 2.552,2.594 0.188,0.167 10 false A 2.802,2.729 3.042,2.896 0.24,0.167 10 false *2 0.5,0.781 0.802,0.938 0.302,0.156 10 false G27 0.302,0.115 0.49,0.281 0.188,0.167 10 false *a 2.125,0.167 2.635,0.344 0.51,0.177 10 false RBE+ 0.74,0.167 1.219,0.333 0.479,0.167 10 false RBE- 1.104,4.333 1.51,4.573 0.406,0.24 10 false RBE+ 1.083,3.427 1.646,3.656 0.563,0.229 10 false GNDR 1.25,3.865 1.552,4.021 0.302,0.156 10 false G64 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.625 1.719,2.781 0.229,0.156 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G27)Location & Routing

Click Connector(G27)Seat>Floor Wire>Front Seat Inner Belt Assembly RH

G27-3 (RBE+) - Body ground Always 1 MΩ or higher
G27-2 (RBE-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E459555C01
0.469,0.76 0.885,1.01 0.417,0.25 1.156,3.823 1.573,4.073 0.417,0.25 1.01,0.219 1.177,0.219 1.177,0.219 1.49,0.708 true 1.5,3.5 1.583,3.5 1.583,3.5 1.906,3.896 true 1.479,4.427 1.646,4.427 1.646,4.427 2.021,4.156 true 2.958,3.406 2.792,3.406 2.792,3.406 2.24,3.865 true 2.094,0.26 1.938,0.26 1.938,0.26 1.667,0.729 true 0.385,2.927 0.573,3.094 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.146,2.438 1.333,2.604 0.188,0.167 10 false C 1.927,2.438 2.115,2.604 0.188,0.167 10 false B 2.375,2.427 2.563,2.594 0.188,0.167 10 false A 2.802,2.698 3.042,2.865 0.24,0.167 10 false *2 0.542,0.802 0.844,0.958 0.302,0.156 10 false G27 0.302,0.115 0.49,0.281 0.188,0.167 10 false *a 2.146,0.146 2.656,0.323 0.51,0.177 10 false RBE+ 0.625,0.146 1.104,0.313 0.479,0.167 10 false RBE- 1.104,4.333 1.51,4.573 0.406,0.24 10 false RBE+ 1.083,3.427 1.646,3.656 0.563,0.229 10 false GNDR 1.25,3.865 1.563,4.021 0.313,0.156 10 false G64 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.625 1.719,2.781 0.229,0.156 10 false *3 3.031,3.344 3.271,3.51 0.24,0.167 10 false *4
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 27 (RBE+) and 18 (GNDR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G27)Location & Routing

Click Connector(G27)Seat>Floor Wire>Front Seat Inner Belt Assembly RH

G27-3 (RBE+) - G27-2 (RBE-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector B.



OK

7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E459554C01
0.427,0.74 0.844,0.99 0.417,0.25 1.167,3.823 1.583,4.073 0.417,0.25 1.125,0.25 1.292,0.25 1.292,0.25 1.469,0.708 true 1.5,3.5 1.583,3.5 1.583,3.5 1.906,3.896 true 1.479,4.427 1.646,4.427 1.646,4.427 2.021,4.156 true 2.021,0.271 1.854,0.271 1.854,0.271 1.667,0.698 true 0.385,2.927 0.573,3.094 0.188,0.167 10 false *1 0.708,2.427 0.896,2.594 0.188,0.167 10 false D 1.125,2.438 1.313,2.604 0.188,0.167 10 false C 1.938,2.427 2.125,2.594 0.188,0.167 10 false B 2.365,2.427 2.552,2.594 0.188,0.167 10 false A 2.802,2.729 3.042,2.896 0.24,0.167 10 false *2 0.5,0.781 0.802,0.938 0.302,0.156 10 false G27 0.302,0.115 0.49,0.281 0.188,0.167 10 false *a 2.125,0.167 2.635,0.344 0.51,0.177 10 false RBE+ 0.74,0.167 1.219,0.333 0.479,0.167 10 false RBE- 1.104,4.333 1.51,4.573 0.406,0.24 10 false RBE+ 1.083,3.427 1.646,3.656 0.563,0.229 10 false GNDR 1.25,3.865 1.552,4.021 0.302,0.156 10 false G64 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.625 1.719,2.781 0.229,0.156 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G27)Location & Routing

Click Connector(G27)Seat>Floor Wire>Front Seat Inner Belt Assembly RH

G27-3 (RBE+) - Body ground Ignition switch ON Below 1 V
G27-2 (RBE-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC
a.
C374693C43
1,1.521 1.313,1.719 0.313,0.198 10 false *1 2.479,1.385 2.792,1.583 0.313,0.198 10 false *2 1.677,1.333 1.99,1.531 0.313,0.198 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the front seat inner belt assembly RH connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC
9.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B005000 is not output A
B005000 is output B


Post-procedure1

a.

None



A

B

10.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and front seat inner belt assembly LH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

11.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

11.CHECK CONNECTORS

Pre-procedure1

a.
C208244C48
0.656,1.354 0.969,1.552 0.313,0.198 10 false *1 2.563,1.781 2.875,1.979 0.313,0.198 10 false *2 1.531,0.594 1.844,0.792 0.313,0.198 10 false *3
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the front seat inner belt assembly LH connector.


Procedure1

a.

Check that the connectors (on the airbag ECU assembly side and front seat inner belt assembly LH side) are not damaged.

OK:

The terminals of the connectors are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

12.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

Pre-procedure1

a.

Remove the front seat inner belt assembly LH.

HINT:

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL



Procedure1

a.

Inspect the front seat inner belt assembly LH.

E454798C01
6.125,1.5 6.292,1.5 6.292,1.5 6.5,1.26 false 5.552,0.844 5.719,0.844 5.719,0.844 5.719,0.604 false 2.344,1.385 2.677,1.052 2.677,1.052 2.844,1.052 false 1.219,0.854 1.021,0.854 1.021,0.854 0.792,1.25 true 2.927,0.969 3.094,1.135 0.167,0.167 10 false *1 5.948,1.427 6.198,1.594 0.25,0.167 10 false *2 0.531,0.698 0.781,0.865 0.25,0.167 10 false *a 5.396,0.792 5.646,0.958 0.25,0.167 10 false *b 1.354,0.781 1.771,0.948 0.417,0.167 10 false LBE-
*1 Front Seat Inner Belt Assembly LH *2 Battery
*a Component without harness connected
(Front Seat Inner Belt Assembly LH)
*b Tester


Standard Current:
Tester Connection Condition Specified Condition
Tester positive (+) - 2 (LBE-)
Tester negative (-) - Battery negative (-)
Seat belt fastened 12.0 to 18.0 mA
Tester positive (+) - 2 (LBE-)
Tester negative (-) - Battery negative (-)
Seat belt not fastened 4.0 to 7.0 mA



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

13.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

13.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)
a.
E454799C01
0.438,0.708 0.865,0.958 0.427,0.25 1.167,3.823 1.583,4.073 0.417,0.25 1.833,0.302 1.667,0.302 1.667,0.302 1.604,0.698 true 0.927,0.292 1.094,0.292 1.094,0.292 1.406,0.667 true 2.906,3.594 2.74,3.594 2.74,3.594 2.479,3.917 true 2.865,4.458 2.698,4.458 2.698,4.458 2.292,4.125 true 0.385,2.448 0.573,2.615 0.188,0.167 10 false *1 0.708,1.979 0.896,2.146 0.188,0.167 10 false D 1.135,1.979 1.323,2.146 0.188,0.167 10 false C 1.948,1.969 2.135,2.135 0.188,0.167 10 false B 2.385,1.958 2.573,2.125 0.188,0.167 10 false A 2.781,2.875 3.021,3.042 0.24,0.167 10 false *2 0.542,0.76 0.844,0.917 0.302,0.156 10 false G25 0.302,0.115 0.49,0.281 0.188,0.167 10 false *a 0.552,0.229 1.063,0.406 0.51,0.177 10 false LBE- 1.865,0.219 2.344,0.385 0.479,0.167 10 false LBE+ 2.927,4.375 3.333,4.615 0.406,0.24 10 false LBE+ 2.948,3.51 3.385,3.677 0.438,0.167 10 false GNDL 1.271,3.875 1.573,4.031 0.302,0.156 10 false G43 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.146 1.719,2.302 0.229,0.156 10 false *3
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G25)Location & Routing

Click Connector(G25)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G25-3 (LBE+) - Body ground Always 1 MΩ or higher
G25-2 (LBE-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E454800C01
0.417,0.76 0.833,1.01 0.417,0.25 1.156,3.823 1.573,4.073 0.417,0.25 1.969,0.26 1.802,0.26 1.802,0.26 1.646,0.708 true 1.021,0.26 1.188,0.26 1.188,0.26 1.427,0.708 true 1.417,3.5 1.583,3.5 1.583,3.5 2.25,4.083 true 2.896,3.469 2.729,3.469 2.729,3.469 2.479,3.896 true 2.719,4.135 3.052,4.135 true 0.396,2.458 0.583,2.625 0.188,0.167 10 false *1 0.708,1.979 0.896,2.146 0.188,0.167 10 false D 1.146,1.979 1.333,2.146 0.188,0.167 10 false C 1.948,1.979 2.135,2.146 0.188,0.167 10 false B 2.385,1.958 2.573,2.125 0.188,0.167 10 false A 2.802,2.885 3.042,3.052 0.24,0.167 10 false *2 0.5,0.802 0.802,0.958 0.302,0.156 10 false G25 0.302,0.115 0.49,0.281 0.188,0.167 10 false *a 0.646,0.188 1.156,0.365 0.51,0.177 10 false LBE- 2.042,0.167 2.521,0.333 0.479,0.167 10 false LBE+ 1.094,3.438 1.5,3.677 0.406,0.24 10 false LBE+ 2.948,3.385 3.365,3.573 0.417,0.188 10 false GNDL 1.26,3.875 1.563,4.031 0.302,0.156 10 false G43 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.177 1.719,2.333 0.229,0.156 10 false *3 3.135,4.052 3.375,4.219 0.24,0.167 10 false *4
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 30 (LBE+) and 24 (GNDL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G25)Location & Routing

Click Connector(G25)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G25-3 (LBE+) - G25-2 (LBE-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector B.



OK

15.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E454799C01
0.438,0.708 0.865,0.958 0.427,0.25 1.167,3.823 1.583,4.073 0.417,0.25 1.833,0.302 1.667,0.302 1.667,0.302 1.604,0.698 true 0.927,0.292 1.094,0.292 1.094,0.292 1.406,0.667 true 2.906,3.594 2.74,3.594 2.74,3.594 2.479,3.917 true 2.865,4.458 2.698,4.458 2.698,4.458 2.292,4.125 true 0.385,2.448 0.573,2.615 0.188,0.167 10 false *1 0.708,1.979 0.896,2.146 0.188,0.167 10 false D 1.135,1.979 1.323,2.146 0.188,0.167 10 false C 1.948,1.969 2.135,2.135 0.188,0.167 10 false B 2.385,1.958 2.573,2.125 0.188,0.167 10 false A 2.781,2.875 3.021,3.042 0.24,0.167 10 false *2 0.542,0.76 0.844,0.917 0.302,0.156 10 false G25 0.302,0.115 0.49,0.281 0.188,0.167 10 false *a 0.552,0.229 1.063,0.406 0.51,0.177 10 false LBE- 1.865,0.219 2.344,0.385 0.479,0.167 10 false LBE+ 2.927,4.375 3.333,4.615 0.406,0.24 10 false LBE+ 2.948,3.51 3.385,3.677 0.438,0.167 10 false GNDL 1.271,3.875 1.573,4.031 0.302,0.156 10 false G43 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.146 1.719,2.302 0.229,0.156 10 false *3
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G25)Location & Routing

Click Connector(G25)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G25-3 (LBE+) - Body ground ignition switch on (IG) Below 1 V
G25-2 (LBE-) - Body ground ignition switch on (IG) Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

16.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CLEAR DTC
a.
C370762C27
0.865,0.948 1.177,1.146 0.313,0.198 10 false *1 2.396,1.292 2.708,1.49 0.313,0.198 10 false *2 1.531,0.667 1.844,0.865 0.313,0.198 10 false *3
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the front seat inner belt assembly LH connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

17.CHECK DTC
17.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B005000 is not output A
B005000 is output B


Post-procedure1

a.

None



A

B