Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448288 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B604620N04
4.219,1.708 4.302,1.542 4.302,1.542 4.552,1.542 false 4.75,0.583 4.833,0.417 4.833,0.417 5,0.417 false 1.938,3.583 2.188,3.583 2.188,3.583 2.271,3.417 false 0.313,2.969 0.583,2.354 0.583,2.354 0.833,2.354 false 6.271,0.677 6.521,0.677 6.521,0.677 6.604,0.844 false 3.281,0.563 3.698,0.563 false 5.344,0.26 5.625,0.615 0.281,0.354 18 false 1 3.063,0.427 3.344,0.781 0.281,0.354 18 false 2 1.76,3.469 2.042,3.823 0.281,0.354 18 false 3 0.906,2.229 1.188,2.583 0.281,0.354 18 false 4 4.781,1.406 5.063,1.76 0.281,0.354 18 false 5 6.688,0.813 7,1.01 0.313,0.198 10 false x 6 2.938,0.469 3.094,0.667 0.156,0.198 10 false ● 4.635,1.448 4.792,1.646 0.156,0.198 10 false ● 6.135,0.583 6.292,0.781 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT DOOR UPPER WINDOW FRAME MOULDING LH 75754A (Click here) - -
2 FRONT DOOR WINDOW FRAME MOULDING LH 75756D (Click here) - -
3 FRONT DOOR WEATHERSTRIP LH 67862 - - -
4 UPPER DOOR FRAME GARNISH LH 67664 - - -
5 FRONT DOOR BELT MOULDING ASSEMBLY LH 75720 - - -

● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75754A 1.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING LH

a.
B599520N02
6.917,0.677 7.073,1.021 0.156,0.344 18 false i 1.677,2.021 1.958,2.375 0.281,0.354 18 false i 0.417,0.104 0.813,0.604 0.396,0.5 18 false ii 1.604,0.104 2.052,0.479 0.448,0.375 18 false iii

i.

Insert the guides, attach the claws and temporarily install the front door upper window frame moulding LH to the door frame.


ii.

Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.


iii.

Press the rivets perpendicularly to the installation holes. Using the air riveter, install the front door upper window frame moulding LH with the 6 rivets.

NOTICE:
·

When installing the rivets to the panel surface, do not tilt the riveter.

·

Do not leave a gap between the rivet head portion and the panel.



HINT:

Pull the trigger again to cut off the rivet if it is not cut off.




Hide 75756D 2.INSTALL FRONT DOOR WINDOW FRAME MOULDING LH

a.
B599521N01
4.365,0.135 4.813,0.406 0.448,0.271 18 false i 2.948,1.01 3.396,1.281 0.448,0.271 18 false iii 4.323,1.49 4.771,1.76 0.448,0.271 18 false ii

i.

Clean the front door panel LH surface:

1. When reusing the front door panel LH, remove remaining double-sided tape from the front door panel LH.

2. Using a heat light, heat the front door panel LH surface.

Standard Value:
Part Temperature
Front Door Panel LH 40 to 60°C (104 to 140°F)
Front Door Window Frame Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front door panel LH excessively.


3. Remove any remaining double-sided tape from the front door panel LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the front door window frame moulding LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new front door panel LH surface.




ii.

Using a heat light, heat the front door panel LH and a new front door window frame moulding LH.

NOTICE:

Do not heat the front door window frame moulding LH and front door panel LH excessively.



iii.

Attach the guide, clip and double-sided tape to install the front door window frame moulding LH.

NOTICE:

The application strength of the front door window frame moulding LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the front door panel LH.




Hide 67862 3.CONNECT FRONT DOOR WEATHERSTRIP LH

Hide 67664 4.INSTALL UPPER DOOR FRAME GARNISH LH

Hide 75720 5.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH