Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448289 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B604627N04
5.563,0.375 5.646,0.208 5.646,0.208 5.896,0.208 false 4.542,0.375 4.792,0.375 4.792,0.375 4.896,0.771 false 3.167,1.365 3.417,1.365 3.417,1.365 3.479,1.25 false 5.865,2.208 5.948,2.375 5.948,2.375 6.198,2.375 false 2.708,0.521 2.958,0.521 2.958,0.521 3.042,0.688 false 5.906,1.292 5.99,1.042 5.99,1.042 6.156,1.042 false 0.906,2.802 1.156,2.802 1.156,2.802 1.24,2.969 false 1.719,3.396 1.969,3.396 1.969,3.396 2.052,3.563 false 5.958,0.115 6.115,0.313 0.156,0.198 10 false ● 2.531,0.458 2.688,0.656 0.156,0.198 10 false ● 6.427,0.979 6.583,1.177 0.156,0.198 10 false ● 6.26,2.292 6.417,2.49 0.156,0.198 10 false ● 6.406,2.25 6.563,2.563 0.156,0.313 18 false 6 1.521,3.281 1.677,3.542 0.156,0.26 18 false 5 0.698,2.667 0.854,2.927 0.156,0.26 18 false 4 6.552,0.927 6.708,1.188 0.156,0.26 18 false 3 2.969,1.229 3.125,1.49 0.156,0.26 18 false 2 4.323,0.24 4.479,0.5 0.156,0.26 18 false 1 3.25,0.583 3.563,0.781 0.313,0.198 10 false x 3 5.646,0.417 5.958,0.615 0.313,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DOOR UPPER WINDOW FRAME MOULDING LH 75764A (Click here) - -
2 REAR DOOR REAR WINDOW FRAME MOULDING LH 75766A (Click here) - -
3 REAR DOOR WINDOW FRAME MOULDING LH 75762B (Click here) - -
4 REAR DOOR WEATHERSTRIP LH 67872 - - -
5 REAR DOOR FRAME GARNISH LH 67674B - - -
6 REAR DOOR BELT MOULDING ASSEMBLY LH 75740 - - -

● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75764A 1.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH

a.
B599526N03
0.344,0.75 0.625,1.104 0.281,0.354 18 false i 4.208,0.031 4.49,0.385 0.281,0.354 18 false ii 5.323,0.042 5.604,0.396 0.281,0.354 18 false iii

i.

Insert the guides and temporarily install the rear door upper window frame moulding LH to the door frame.


ii.

Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.


iii.

Press the rivets perpendicularly to the installation holes. Using the air riveter, install the rear door upper window frame moulding LH with the 4 rivets.

NOTICE:
·

When installing the rivets to the panel surface, do not tilt the riveter.

·

Do not leave a gap between the rivet head portion and the panel.



HINT:

Pull the trigger again to cut off the rivet if it is not cut off.




Hide 75766A 2.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING LH

a.
B599527N03
2.229,0.354 2.51,0.708 0.281,0.354 18 false i 3.542,0.083 3.823,0.438 0.281,0.354 18 false ii 4.635,0.083 4.917,0.438 0.281,0.354 18 false iii

i.

Insert the guides and temporarily install the rear door rear window frame moulding LH to the door frame.


ii.

Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.


iii.

Press the rivets perpendicularly to the installation holes. Using the air riveter, install the rear door rear window frame moulding LH with the 3 rivets.

NOTICE:
·

When installing the rivets to the panel surface, do not tilt the riveter.

·

Do not leave a gap between the rivet head portion and the panel.



HINT:

Pull the trigger again to cut off the rivet if it is not cut off.




Hide 75762B 3.INSTALL REAR DOOR WINDOW FRAME MOULDING LH

a.
B599528N01
0.979,0.156 1.49,0.438 0.51,0.281 18 false i 3.656,1.469 4.167,1.75 0.51,0.281 18 false iii 0.969,1.521 1.479,1.802 0.51,0.281 18 false ii

i.

Clean the rear door panel LH surface:

1. When reusing the rear door panel LH, remove remaining double-sided tape from the rear door panel LH.

2. Using a heat light, heat the rear door panel LH surface.

Standard Value:
Part Temperature
Rear Door Panel LH 40 to 60°C (104 to 140°F)
Rear Door Window Frame Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door panel LH excessively.


3. Remove any remaining double-sided tape from the rear door panel LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the rear door window frame moulding LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear door panel LH surface.




ii.

Using a heat light, heat the rear door panel LH and a new rear door window frame moulding LH.

NOTICE:

Do not heat the rear door window frame moulding LH and rear door panel LH excessively.



iii.

Attach the guide, clip and double-sided tape to install the rear door window frame moulding LH.

NOTICE:

The application strength of the rear door window frame moulding LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear door panel LH.




Hide 67872 4.CONNECT REAR DOOR WEATHERSTRIP LH

Hide 67674B 5.INSTALL REAR DOOR FRAME GARNISH LH

Hide 75740 6.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH