Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448290 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B604653N02
3.552,1.417 3.802,1.417 3.802,1.417 3.885,1.583 false 2.167,0.74 2.25,0.573 2.25,0.573 2.375,0.573 false 4.604,1.479 4.719,1.052 4.719,1.052 4.948,1.052 false 4.958,1.667 5.01,1.49 5.01,1.49 5.188,1.49 false 3.375,1.313 3.656,1.667 0.281,0.354 18 false 4 5.156,0.917 5.375,1.188 0.219,0.271 18 false 3 2.438,0.438 2.719,0.792 0.281,0.354 18 false 2 5.01,0.958 5.167,1.156 0.156,0.198 10 false ● 5.656,1.354 5.938,1.708 0.281,0.354 18 false 1 5.521,1.396 5.677,1.594 0.156,0.198 10 false ● 4.729,1.344 5.188,1.542 0.458,0.198 10 false x 5 5.156,1.667 5.615,1.865 0.458,0.198 10 false x 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP 75547C (Click here) - -
2 WINDSHIELD GLASS 56111 - - -
3 NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP 75545B - - -
4 LOWER WINDSHIELD MOULDING OUTSIDE LH 75536D - - -

● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75547C 1.INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

a.
B604654N02
0.385,0.083 0.667,0.438 0.281,0.354 18 false i 1.958,0.083 2.24,0.438 0.281,0.354 18 false ii

i.

Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new No. 3 windshield outside moulding clip into the nose piece.


ii.

Press the No. 3 windshield outside moulding clips perpendicularly to the installation holes. Using the air riveter, install the 5 No. 3 windshield outside moulding clips.

NOTICE:
·

When installing the No. 3 windshield outside moulding clips to the panel surface, do not tilt the riveter.

·

Do not leave a gap between the No. 3 windshield outside moulding clip head portion and the panel.



HINT:

Pull the trigger again to cut off the No. 3 windshield outside moulding clip if it is not cut off.




Hide 56111 2.INSTALL WINDSHIELD GLASS

Hide 75545B 3.INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

Hide 75536D 4.INSTALL LOWER WINDSHIELD MOULDING OUTSIDE LH