Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448291 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B599603N02
0.25,1.25 7,3 6.75,1.75 2.51,0.063 7.01,1.146 4.5,1.083 1.396,2.615 1.646,2.615 1.646,2.615 1.729,2.781 false 2.74,2.188 2.823,2.354 2.823,2.354 3.073,2.354 false 4.031,0.313 4.281,0.313 4.281,0.313 4.365,0.479 false 3.771,0.854 4.021,0.854 4.021,0.854 4.104,0.688 false 5.521,0.542 5.604,0.708 5.604,0.708 5.854,0.708 false 5.885,1.708 6.167,1.708 6.167,1.708 6.25,1.542 false 0.323,1.313 0.698,1.552 0.375,0.24 12 false *B 2.563,0.135 2.938,0.375 0.375,0.24 12 false *A 3.302,2.229 3.583,2.583 0.281,0.354 18 false 2 3.844,0.177 4.125,0.531 0.281,0.354 18 false 2 1.063,2.521 1.604,2.75 0.542,0.229 10 false ● 1.219,2.49 1.5,2.844 0.281,0.354 18 false 1 5.708,1.552 5.99,1.906 0.281,0.354 18 false 1 6.354,0.542 6.635,0.896 0.281,0.354 18 false 1 3.438,0.75 3.979,0.979 0.542,0.229 10 false ● 6.219,0.594 6.76,0.823 0.542,0.229 10 false ● 5.563,1.594 6.104,1.823 0.542,0.229 10 false ● 3.583,0.698 3.865,1.052 0.281,0.354 18 false 1 3.135,2.292 3.677,2.521 0.542,0.229 10 false ● 3.677,0.208 4.219,0.438 0.542,0.229 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP 75561 (Click here) - -
2 CENTER ROOF DRIP SIDE FINISH MOULDING LH 75556C - - -

*A for Panoramic Moon Roof *B for Normal Roof
● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75561 1.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

Z101186

HINT:

Perform the following procedure only when replacement of the No. 1 roof drip side finish moulding clip is necessary.



a.
B599691C03
4.604,0.219 4.854,0.219 4.854,0.219 4.906,0.323 false 3.927,0.552 4.177,0.552 4.177,0.552 4.26,0.719 false 1.948,0.083 2.167,0.365 0.219,0.281 18 false i 3.844,0.083 4.063,0.365 0.219,0.281 18 false ii 5.75,0.104 5.969,0.385 0.219,0.281 18 false iii 0.104,0.104 0.479,0.344 0.375,0.24 12 false *A 0.104,3.125 0.479,3.365 0.375,0.24 12 false *B 4.417,0.146 4.729,0.344 0.313,0.198 10 false *a 3.76,0.479 4.073,0.677 0.313,0.198 10 false *b 0.625,1.406 0.792,1.604 0.167,0.198 10 false A 0.625,2.26 0.792,2.458 0.167,0.198 10 false B 4.375,2.885 4.542,3.083 0.167,0.198 10 false C 4.375,3.667 4.542,3.865 0.167,0.198 10 false D 3.042,4.677 3.208,4.875 0.167,0.198 10 false E 2.646,5.521 2.813,5.719 0.167,0.198 10 false F 0.271,0.708 0.49,0.99 0.219,0.281 18 false iv 4.01,2.156 4.229,2.438 0.219,0.281 18 false iv 2.271,4 2.49,4.281 0.219,0.281 18 false iv
*A for Panoramic Moon Roof *B for Normal Roof
*a Adhesive *b 2 to 3 mm (0.0787 to 0.1181 in.)Bead of Adhesive


Standard Measurement:
Area Measurement Area Measurement
A 2.4 mm (0.0945 in.) B 1.1 mm (0.0433 in.)
C 4.1 mm (0.161 in.) D 1.3 mm (0.0512 in.)
E 4.1 mm (0.161 in.) F 1.5 mm (0.0591 in.)


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

Standard Value:
Part Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


2. Remove the double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 1 roof drip side finish moulding clip with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new No. 1 roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



iii.

Apply primer to the body where the No. 1 roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



iv.

While using the position shown in the illustration as a reference, place the No. 1 roof drip side finish moulding clip onto the roof panel. Then position and install the clip using the locations on the roof panel after lightly pressing it so that the adhesive adheres to the primer.

NOTICE:

Install the center roof drip side finish moulding LH when 40 minutes or more have elapsed after pressing and installing the No. 1 roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours





Hide 75556C 2.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING LH