Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  P1F09  Open in High Voltage Electric Heater STB Circuit  


DESCRIPTION

The air conditioning amplifier assembly uses the target blower temperature to calculate the target water temperature, and selects the electric heater sub-assembly drive level based on the water temperature sensor value.

The air conditioning amplifier assembly sends the drive level to the EV control ECU via the CAN communication system, and the EV control ECU drives the electric heater sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
P1F09 Open in High Voltage Electric Heater STB Circuit The air conditioning amplifier assembly stores this DTC if it detects a malfunction in the electric heater sub-assembly.
Diagnosis condition:

When electric heater sub-assembly is driven


Malfunction status:

Electric heater sub-assembly drive signal is short


Detection time:

Electric heater sub-assembly drive line is short


·

Hybrid control system

·

Harness or connector

·

EV control ECU

·

Electric heater sub-assembly


Memorized Air Conditioner B

WIRING DIAGRAM

E457276E01
0.146,1.219 2.5,1.417 2.354,0.198 10 false Air Conditioning Amplifier Assembly 5.167,3.625 6.865,3.823 1.698,0.198 10 false EV Control ECU 5.146,3.458 5.583,3.625 0.438,0.167 10 false A17 5.813,2.031 6.25,2.198 0.438,0.167 10 false AD 4.917,1.906 5.354,2.073 0.438,0.167 10 false LIN4 4.938,3.031 5.375,3.198 0.438,0.167 10 false STB 4.594,1.875 5.031,2.042 0.438,0.167 10 false 12 4.615,2.938 5.052,3.104 0.438,0.167 10 false 19 3.594,3.042 4.031,3.208 0.438,0.167 10 false STB 3.552,2.031 3.99,2.198 0.438,0.167 10 false BLIN 2.906,2.052 3.344,2.219 0.438,0.167 10 false PWR 2.896,3.042 3.333,3.208 0.438,0.167 10 false GND1 3.99,1.865 4.427,2.031 0.438,0.167 10 false 4 4.01,2.948 4.448,3.115 0.438,0.167 10 false 5 2.656,1.958 3.094,2.125 0.438,0.167 10 false 3 2.667,2.948 3.104,3.115 0.438,0.167 10 false 6 1.917,2.198 2.604,2.375 0.688,0.177 10 false A/C NO.1 0.396,2.021 1.5,2.219 1.104,0.198 10 false from A/C Relay 0.833,3.958 2.927,4.146 2.094,0.188 10 false : CAN Communication Line 0.854,4.396 2.677,4.594 1.823,0.198 10 false : LIN Communication Line 2.573,3.469 3.01,3.635 0.438,0.167 10 false B2 2.573,3.625 4.458,3.865 1.885,0.24 10 false Electric Heater Sub-assembly

CAUTION / NOTICE / HINT

CAUTION:
·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ELECTRIC HEATER SUB-ASSEMBLY - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the B2 electric heater sub-assembly connector.


b.

Disconnect the A17 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B2,A17)Location & Routing

Click Connector(B2)Engine Compartment>No. 2 Stack Wire>Electric Heater Sub-Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

B2-5 (STB) - A17-19 (STB) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE ELECTRIC HEATER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR