| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | CAUTIONS FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed)) | - | ( )
|
- | - |
| 2 | SERVICE PLUG GRIP | G3834 | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 9 | FRONT COMPARTMENT UNDER COVER | 51441N | - | - | - |
| 10 | FRONT LOWER SUSPENSION MEMBER PROTECTOR | 51219 | - | - | - |
| 11 | FRONT COMPARTMEMT UNDER COVER ASSEMBLY | 51420A | - | - | - |
| ● | Non-reusable part | ★ | Precoated part |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the electric heater sub-assembly removal/installation are shown below.
This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.
Be sure to wear insulating gloves when working on high voltage wiring or components.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. CAUTIONS FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))
G3834
2.REMOVE SERVICE PLUG GRIP
53292A
3.REMOVE UPPER RADIATOR SUPPORT SEAL
1A906
4.REMOVE FC STACK COVER SUB-ASSEMBLY
51441N
9.REMOVE FRONT COMPARTMENT UNDER COVER
51219
10.REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR
51420A
11.REMOVE FRONT COMPARTMEMT UNDER COVER ASSEMBLY
12.DRAIN COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))
87209C
13.DISCONNECT WATER HOSE SUB-ASSEMBLY C
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly C.
Do not apply excessive force to the water hose sub-assembly C.
Prepare a drain pan or cloth in case the coolant leaks.
87209B
14.DISCONNECT WATER HOSE SUB-ASSEMBLY B
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly B.
Do not apply excessive force to the water hose sub-assembly B.
Prepare a drain pan or cloth in case the coolant leaks.
87101G
15.REMOVE ELECTRIC HEATER SUB-ASSEMBLY
| *a | Connector (A) | *b | Connector (B) |
| *c | Green-colored Lock | - | - |
|
Slide | - | - |
Slide the green-colored lock of the connector (A) as shown in the illustration to release it and disconnect the connector.
Make sure to wear insulating gloves.
Insulate the disconnected terminals and connector with vinyl tape.
Disconnect the connector (B).
Remove the 3 bolts and electric heater sub-assembly.