Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P010031  Mass or Volume Air Flow Sensor "A" No Signal  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor)

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater)

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction)


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly, and uses it to determine the fuel injection duration necessary for an optimal air-fuel ratio.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the heater temperature at a specific temperature.

A403052C01
5.479,1.854 6.333,2.75 6.333,2.75 6.583,2.75 true 5.917,2.906 6.333,3.417 6.333,3.417 6.583,3.417 true 5.25,2.333 4.917,2.667 4.917,2.667 4.667,2.667 true 2.688,2.083 3.083,2.333 3.083,2.333 3.333,2.333 true 3.063,2 3.25,2.083 3.25,2.083 3.5,2.083 true 2.333,1.333 2.917,1.583 2.917,1.583 3.167,1.583 true 1.417,1.583 1.667,1.583 1.667,1.583 2.094,1.417 true 1.25,2.25 1.5,2.25 1.5,2.25 1.802,2.083 true 4.667,0.583 4.917,0.75 0.25,0.167 10 false *1 6.667,2.677 6.917,2.833 0.25,0.156 10 false *a 4.5,2.583 4.75,2.75 0.25,0.167 10 false *b 3.25,1.51 3.5,1.667 0.25,0.156 10 false *c 1.25,1.5 1.5,1.667 0.25,0.167 10 false *d 3.583,2.01 3.896,2.167 0.313,0.156 10 false *e 3.417,2.26 3.729,2.417 0.313,0.156 10 false *f 1.083,2.167 1.333,2.323 0.25,0.156 10 false *g 6.667,3.344 6.917,3.5 0.25,0.156 10 false *h
*1 Mass Air Flow Meter Sub-assembly - -
*a Silicon Chip Sensor *b By-pass Duct
*c Heater *d Heater Thermistor
*e Intake Air *f Temperature Sensor (After Heater)
*g Temperature Sensor (Before Heater) *h Air Flow


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P010031 Mass or Volume Air Flow Sensor "A" No Signal If the +B voltage is not low when the ignition switch is ON, the output frequency of the mass air flow meter sub-assembly is less than 0.1 kHz and such a frequency continues for 3 seconds or more:
(1 trip detection logic)
·

Mass air flow meter sub-assembly

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ ○

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P010031 Mass Air Flow Sensor Frequency

HINT:

It is suspected that the mass air flow sensor sub-assembly is malfunctioning, an open circuit has occurred, or there is something wrong with the mass air flow meter power voltage.


WIRING DIAGRAM

A477028E04
4.792,2.958 5.25,3.156 0.458,0.198 10 false A16 4.792,3.115 6.198,3.427 1.406,0.313 10 false EV Control ECU 4.75,2.198 5.208,2.396 0.458,0.198 10 false GAFM 4.49,2.198 4.802,2.396 0.313,0.198 10 false 23 4.771,1.698 5.219,1.906 0.448,0.208 10 false AFMF 4.5,1.698 4.958,1.896 0.458,0.198 10 false 25 4.781,1.104 5.396,1.302 0.615,0.198 10 false VAFF 4.5,1.094 4.813,1.292 0.313,0.198 10 false 27 0.823,2.719 1.281,2.917 0.458,0.198 10 false A49 0.813,2.885 3.333,3.198 2.521,0.313 10 false Mass Air Flow Meter Sub-assembly 2.875,2.208 3.031,2.406 0.156,0.198 10 false 2 2.458,2.198 2.917,2.396 0.458,0.198 10 false E2G 2.885,1.667 3.042,1.865 0.156,0.198 10 false 1 2.542,1.677 2.854,1.875 0.313,0.198 10 false FG 2.875,1.115 3.063,1.354 0.188,0.24 10 false 3 2.458,1.208 2.802,1.406 0.344,0.198 10 false VCC 5.479,0.823 5.938,1.021 0.458,0.198 10 false 5 V 5.458,1.406 5.917,1.604 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 5 seconds or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)

Pre-procedure1

a.
A476943

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A49)Location & Routing

Click Connector(A49)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Intake Mass Air Flow Meter Sub-Assembly

A49-3 (VCC) - A49-2 (E2G) Ignition switch ON 4.8 to 5.2 V
A49-1 (FG) - A49-2 (E2G) Ignition switch ON 4.8 to 5.2 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the mass air flow meter sub-assembly connector.



OK

2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EV CONTROL ECU)
2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>INTAKE AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch off and wait for 5 seconds or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P010031 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

END

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A49,A16)Location & Routing

Click Connector(A49)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Intake Mass Air Flow Meter Sub-Assembly

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A49-3 (VCC) - A16-27 (VAFF) Always Below 1 Ω
A49-1 (FG) - A16-25 (AFMF) Always Below 1 Ω
A49-2 (E2G) - A16-23 (GAFM) Always Below 1 Ω
A49-3 (VCC) or A16-27 (VAFF) - Body ground and other terminals Always 10 kΩ or higher
A49-1 (FG) or A16-25 (AFMF) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the mass air flow meter sub-assembly connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR