Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P011011  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground  P011015  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature.

The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the EV control ECU as voltage changes.

The intake air temperature sensor is connected to the EV control ECU, and a power voltage of 5 V is supplied from the AFMT terminal of the EV control ECU to the sensor via resistor R. Since resistor R and the sensor are connected in series, resistance varies as an intake air temperature changes, and potential of the AFMT terminal also varies.

A283580E11
3.354,2.271 3.74,1.99 false 3.292,4.271 4.167,4.5 0.875,0.229 10 false Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 false (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 false 30 2.281,1.583 2.521,1.802 0.24,0.219 10 false 10 2.354,1.875 2.594,2.094 0.24,0.219 10 false 5 2.354,2.094 2.594,2.313 0.24,0.219 10 false 3 2.354,2.26 2.51,2.479 0.156,0.219 10 false 2 2.344,2.531 2.594,2.75 0.25,0.219 10 false 1 2.24,2.833 2.479,3.052 0.24,0.219 10 false 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 false 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 false 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 false 20 2.542,3.823 2.781,4.042 0.24,0.219 10 false -20 2.938,3.823 3.177,4.042 0.24,0.219 10 false 0 3.208,3.823 3.448,4.042 0.24,0.219 10 false 20 3.521,3.823 3.76,4.042 0.24,0.219 10 false 40 3.833,3.823 4.073,4.042 0.24,0.219 10 false 60 4.146,3.823 4.385,4.042 0.24,0.219 10 false 80 4.385,3.823 4.625,4.042 0.24,0.219 10 false 100 2.583,4 2.823,4.219 0.24,0.219 10 false -4 2.896,4 3.135,4.219 0.24,0.219 10 false 32 3.208,4 3.448,4.219 0.24,0.219 10 false 68 3.479,4 3.729,4.25 0.25,0.25 10 false 104 3.792,4 4.125,4.25 0.333,0.25 10 false 140 4.094,4 4.417,4.25 0.323,0.25 10 false 176 4.385,4 4.708,4.25 0.323,0.25 10 false 212 4.677,3.823 5,4.073 0.323,0.25 10 false (°C) 4.677,4 5,4.25 0.323,0.25 10 false (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 false Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 false Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 false 0.3

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P011011 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground If the +B voltage is not low when the ignition switch is ON, the output voltage of the intake air temperature sensor circuit remains at less than 0.1 V (short circuit) for more than 3 seconds.
(1 trip detection logic)
·

Mass air flow meter sub-assembly

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A
P011015 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open If the +B voltage is not low when the ignition switch is ON, the output voltage of the intake air temperature sensor circuit remains at more than 4.9V (open circuit) for more than 3 seconds.
(1 trip detection logic)
·

Mass air flow meter sub-assembly

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is travelling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List
DTC No. Data List
P011011 Intake Air Temperature (Filtered Value)
P011015

WIRING DIAGRAM

A477011E02
2.427,1.333 2.885,1.531 0.458,0.198 10 false THA 2.438,1.938 2.896,2.135 0.458,0.198 10 false E2G 5.271,1.323 5.729,1.521 0.458,0.198 10 false AFMT 5.26,1.917 5.719,2.115 0.458,0.198 10 false GAFM 2.854,1.333 3.313,1.531 0.458,0.198 10 false 4 2.865,1.927 3.323,2.125 0.458,0.198 10 false 2 5,1.323 5.458,1.521 0.458,0.198 10 false 26 4.99,1.917 5.448,2.115 0.458,0.198 10 false 23 5.729,0.938 6.188,1.135 0.458,0.198 10 false 5 V 5.438,2.969 5.958,3.229 0.521,0.26 10 false A16 5.427,3.125 6.438,3.406 1.01,0.281 10 false EV Control ECU 0.469,3.052 0.927,3.25 0.458,0.198 10 false A49 0.458,3.208 3.292,3.49 2.833,0.281 10 false Mass Air Flow Meter Sub-assembly 0.615,2.302 2.698,2.594 2.083,0.292 10 false Intake Air Temperature Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE (FILTERED VALUE))
a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Intake Air Temperature (Filtered Value)
50003 397 894
Result:
Result Proceed to
The value of Intake Air Temperature (Filtered Value) is -40 °C A
The value of Intake Air Temperature (Filtered Value) is 140 °C B


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Pre-procedure1

a.
A476943

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect terminals 4 (THA) and 2 (E2G) of the mass air flow meter sub-assembly connector on the wire harness side.

A376960C45
4.49,1.427 4.833,1.667 0.344,0.24 5.313,2.073 5.583,1.552 true 6.219,2.083 5.958,1.552 true 4.563,1.479 4.875,1.677 0.313,0.198 10 false A49 4.135,0.677 4.448,0.875 0.313,0.198 10 false *a 1.135,0.719 1.448,0.917 0.313,0.198 10 false *1 2.781,0.688 3.146,0.875 0.365,0.188 10 false *2 5.135,2.083 5.5,2.271 0.365,0.188 10 false E2G 6.125,2.083 6.49,2.271 0.365,0.188 10 false THA
*1 Mass Air Flow Meter Sub-assembly *2 EV Control ECU
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
- -



Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Intake Air Temperature (Filtered Value)
50003 397 894

Result:
Result Proceed to
The value of Intake Air Temperature (Filtered Value) is 140 °C A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the mass air flow meter sub-assembly connector.



A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - MASS AIR FLOW METER SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - MASS AIR FLOW METER SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the mass air flow meter sub-assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A49)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A49)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Intake Mass Air Flow Meter Sub-Assembly

A16-26 (AFMT) - A49-4 (THA) Always Below 1 Ω
A16-23 (GAFM) - A49-2 (E2G) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the mass air flow meter sub-assembly connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

Pre-procedure1

a.
A476943

Disconnect the mass air flow meter sub-assembly connector.


Procedure1

a.
A335356C01
0.698,0.458 1.01,0.656 0.313,0.198 10 false *1 2.604,0.26 2.917,0.458 0.313,0.198 10 false *2
*1 Mass Air Flow Meter Sub-assembly
*2 EV Control ECU


Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Intake Air Temperature (Filtered Value)
50003 397 894

Result:
Result Proceed to
The value of Intake Air Temperature (Filtered Value) is -40 °C A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the mass air flow meter sub-assembly connector.



A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - MASS AIR FLOW METER SUB-ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - MASS AIR FLOW METER SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the mass air flow meter sub-assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A49)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A49)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Intake Mass Air Flow Meter Sub-Assembly

A16-26 (AFMT) or A49-4 (THA) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the mass air flow meter sub-assembly connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR