The FC control ECU monitors its internal operation and will store these DTCs when it detects an internal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P060B1C | Internal Control Module A/D Processing Performance Circuit Voltage Out of Range | When the +B voltage is not low with the ignition switch ON, an ECU internal error occurs. (Abnormal AD conversion)
(1 trip detection logic) |
FC control ECU | Master Warning: Comes on | FC | B |
| P060B49 | Internal Control Module A/D Processing Performance Internal Electronic Failure | When the +B voltage is not low with the ignition switch ON, an ECU internal error occurs. (Timeout)
(1 trip detection logic) |
FC control ECU | Master Warning: Comes on | FC | B |
| P060B71 | Internal Control Module A/D Processing Performance Actuator Stuck | When the +B voltage is not low with the ignition switch ON, an ECU internal error occurs. (Abnormal multiplexer)
(1 trip detection logic) |
FC control ECU | Master Warning: Comes on | FC | B |
| Vehicle Condition | FC shutdown
(ignition switch ON) |
FC startup process | FC intermittent operation | FC is generating power
(vehicle is in stationary) |
FC is generating power
(vehicle is traveling) |
FC shutdown process |
|---|---|---|---|---|---|---|
| Data List (EV)
"FC Work Mode" |
Stop | Startup | Working | Finishing | ||
| Data List (EV)
"FC Intermittent Operation" |
OFF | ON | OFF | OFF | ||
| DTC Detection | ○ | ○ | ○ | ○ | ○ | ○ |
| DTC No. | Data List |
|---|---|
| P060B1C | ·
High-Range Hydrogen Pressure Sensor Voltage ·
Medium-Range Hydrogen Pressure Sensor Voltage ·
Low-Range Hydrogen Pressure Sensor Voltage ·
Air Shunt Valve Position Sensor Voltage ·
Air Sealing Valve Position Sensor Voltage ·
Air Pressure Regulating Valve Position Sensor Voltage |
| P060B49 | |
| P060B71 |
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch off and wait for 10 minutes or more.
Turn the ignition switch to ON and wait for 15 seconds or more.
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for 10 minutes or more.
NEXT
Pre-procedure1
Turn the ignition switch to ON and wait for 5 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P060B1C, P060B49 or P060B71 is output | A |
| P060B1C, P060B49 or P060B71 and other DTCs are output | B |
| DTCs are not output | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING