Home › Engine / Hybrid System › FC CONTROL › FC CONTROL ECU
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466403 FC CONTROL ECU A

FC CONTROL  FC CONTROL ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A475819N03
3.958,1.167 4.188,1.167 true 2.729,1.188 2.896,1.188 2.896,1.188 3.094,0.927 true 6.417,0.271 6.833,0.271 true 6.427,0.667 6.792,0.667 true 6.229,2.146 6.479,1.823 6.479,1.823 6.646,1.823 true 2.448,2.344 2.615,2.344 2.615,2.344 2.813,2.083 true 6.26,0.146 6.542,0.5 0.281,0.354 18 false 1 6.729,1.688 7.01,2.042 0.281,0.354 18 false 3 6.26,0.542 6.542,0.896 0.281,0.354 18 false 2 2.271,2.219 2.552,2.573 0.281,0.354 18 false 5 2.563,1.052 2.844,1.406 0.281,0.354 18 false 6 4.552,1.042 4.833,1.396 0.281,0.354 18 false 4 5.667,1.344 5.979,1.542 0.313,0.198 10 false x 6 2.24,1.885 2.552,2.083 0.313,0.198 10 false x 2 2.656,0.76 2.969,0.958 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 UPPER RADIATOR SUPPORT SEAL 53292A - - -
4 FC CONTROL ECU 898A1 (Click here) - -
5 NO. 1 FC CONTROL ECU BRACKET 898A7 - - -
6 NO. 2 FC CONTROL ECU BRACKET 898A8 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the FC control ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 898A1 4.REMOVE FC CONTROL ECU

a.
A475815N01
0.406,0.042 0.688,0.396 0.281,0.354 18 false i 4.479,0.042 4.76,0.396 0.281,0.354 18 false ii

i.

Lift up the lever to detach the lock, and disconnect the 2 FC control ECU connectors from the FC control ECU.

NOTICE:

When disconnecting connectors, make sure that foreign substances such as mud or water droplets do not adhere to them.



ii.

Remove the 2 bolts and FC control ECU.

NOTICE:

If the FC control ECU is dropped or subjected to a strong impact, replace it with a new one.




Hide 898A7 5.REMOVE NO. 1 FC CONTROL ECU BRACKET

a.
A475816


Hide 898A8 6.REMOVE NO. 2 FC CONTROL ECU BRACKET

a.
A475817