Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D2511  Radiator Outlet Coolant Temperature Sensor Circuit Short to Ground  P1D2515  Radiator Outlet Coolant Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

The water temperature sensor (for radiator outlet side) has a built-in thermistor with a resistance that varies according to the temperature of the FC coolant. When the FC coolant temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the EV control ECU as voltage changes.

The water temperature sensor (for radiator outlet side) is connected to the EV control ECU, and a power voltage of 5 V is supplied from the WTR terminal of the EV control ECU to the sensor via resistor R. Since resistor R and the sensor are connected in series, resistance varies as an FC stack coolant temperature changes, and potential of the WTR terminal also varies.

A283580E12
3.354,2.271 3.74,1.99 false 3.292,4.271 4.167,4.5 0.875,0.229 10 false Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 false (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 false 30 2.281,1.583 2.521,1.802 0.24,0.219 10 false 10 2.354,1.875 2.594,2.094 0.24,0.219 10 false 5 2.354,2.094 2.594,2.313 0.24,0.219 10 false 3 2.354,2.26 2.51,2.479 0.156,0.219 10 false 2 2.344,2.531 2.594,2.75 0.25,0.219 10 false 1 2.24,2.833 2.479,3.052 0.24,0.219 10 false 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 false 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 false 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 false 20 2.542,3.823 2.781,4.042 0.24,0.219 10 false -20 2.938,3.823 3.177,4.042 0.24,0.219 10 false 0 3.208,3.823 3.448,4.042 0.24,0.219 10 false 20 3.521,3.823 3.76,4.042 0.24,0.219 10 false 40 3.833,3.823 4.073,4.042 0.24,0.219 10 false 60 4.146,3.823 4.385,4.042 0.24,0.219 10 false 80 4.385,3.823 4.625,4.042 0.24,0.219 10 false 100 2.583,4 2.823,4.219 0.24,0.219 10 false -4 2.896,4 3.135,4.219 0.24,0.219 10 false 32 3.208,4 3.448,4.219 0.24,0.219 10 false 68 3.479,4 3.729,4.25 0.25,0.25 10 false 104 3.792,4 4.125,4.25 0.333,0.25 10 false 140 4.094,4 4.417,4.25 0.323,0.25 10 false 176 4.385,4 4.708,4.25 0.323,0.25 10 false 212 4.677,3.823 5,4.073 0.323,0.25 10 false (°C) 4.677,4 5,4.25 0.323,0.25 10 false (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 false Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 false Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 false 0.3

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D2511 Radiator Outlet Coolant Temperature Sensor Circuit Short to Ground If the +B voltage is not low when the ignition switch is turned to ON, the output voltage of the water temperature sensor (for radiator outlet side) circuit remains at less than 0.1 V for more than 3 seconds.
(1 trip detection logic)
·

Water temperature sensor (for radiator outlet side)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A
P1D2515 Radiator Outlet Coolant Temperature Sensor Circuit Short to Battery or Open If the +B voltage is not low when the ignition switch is turned to ON, the output voltage of the water temperature sensor (for radiator outlet side) circuit remains at more than 4.9 V for more than 3 seconds.
(1 trip detection logic)
·

Water temperature sensor (for radiator outlet side)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List
DTC No. Data List
P1D2511
·

Radiator Outlet Coolant Temperature Sensor Voltage

·

Radiator Outlet Coolant Temperature (Filtered Value)


P1D2515

WIRING DIAGRAM

A335331E16
2.01,1.344 2.469,1.542 0.458,0.198 10 false WTR 1.906,1.948 2.365,2.146 0.458,0.198 10 false GWTR 4.583,1.333 5.042,1.531 0.458,0.198 10 false WTR 4.583,1.938 5.042,2.135 0.458,0.198 10 false GWTR 2.417,1.344 2.875,1.542 0.458,0.198 10 false 1 2.417,1.938 2.875,2.135 0.458,0.198 10 false 2 4.333,1.333 4.792,1.531 0.458,0.198 10 false 25 4.333,1.948 4.792,2.146 0.458,0.198 10 false 33 5.729,0.938 6.188,1.135 0.458,0.198 10 false 5 V 5,2.958 5.521,3.219 0.521,0.26 10 false A15 5,3.104 6.656,3.344 1.656,0.24 10 false EV Control ECU 0.74,2.625 1.198,2.823 0.458,0.198 10 false A50 0.74,2.792 2.406,3.427 1.667,0.635 10 false Water Temperature Sensor (for Radiator Outlet Side)

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.READ VALUE USING GTS (RADIATOR OUTLET COOLANT TEMPERATURE SENSOR VOLTAGE)
a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Radiator Outlet Coolant Temperature Sensor Voltage
50003 397 903
Result:
Result Proceed to
The value of Radiator Outlet Coolant Temperature Sensor Voltage is more than 4.9 V A
The value of Radiator Outlet Coolant Temperature Sensor Voltage is less than 0.1 V B


HINT:
·

If there is an open circuit, the GTS indicates more than 4.9 V.

·

If there is a short circuit, the GTS indicates less than 0.1 V.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Pre-procedure1

a.
A476948

Disconnect the water temperature sensor (for radiator outlet side) connector.


b.
A361589C11
0.552,2.615 0.938,2.844 0.385,0.229 1.104,3.146 1.573,2.781 true 2.333,3.135 1.802,2.792 true 0.646,0.271 0.844,0.458 0.198,0.188 10 false *1 2.635,0.271 2.948,0.469 0.313,0.198 10 false *2 0.344,2 0.656,2.198 0.313,0.198 10 false *a 0.635,2.656 0.948,2.854 0.313,0.198 10 false A50 0.885,3.198 1.292,3.427 0.406,0.229 10 false WTR 2.26,3.177 2.76,3.406 0.5,0.229 10 false GWTR
*1 Water Temperature Sensor (for Radiator Outlet Side)
*2 EV Control ECU
*a Front view of wire harness connector
(to Water Temperature Sensor (for Radiator Outlet Side))


Connect terminals 1 (WTR) and 2 (GWTR) of the water temperature sensor (for radiator outlet side) connector on the wire harness side.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Radiator Outlet Coolant Temperature Sensor Voltage
50003 397 903

Result:
Result Proceed to
The value of Radiator Outlet Coolant Temperature Sensor Voltage is less than 0.1 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the water temperature sensor (for radiator outlet side) connector.



A

REPLACE WATER TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE)

B

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE))
3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the water temperature sensor (for radiator outlet side) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A15,A50)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A50)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Engine Coolant Temperature Sensor

A15-25 (WTR) - A50-1 (WTR) Always Below 1 Ω
A15-33 (GWTR) - A50-2 (GWTR) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the water temperature sensor (for radiator outlet side) connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

Pre-procedure1

a.
A476948

Disconnect the water temperature sensor (for radiator outlet side) connector.


Procedure1

a.
A335356C02
0.719,0.469 1.031,0.667 0.313,0.198 10 false *1 2.604,0.302 2.917,0.5 0.313,0.198 10 false *2
*1 Water Temperature Sensor (for Radiator Outlet Side)
*2 EV Control ECU


Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Radiator Outlet Coolant Temperature Sensor Voltage
50003 397 903

Result:
Result Proceed to
The value of Radiator Outlet Coolant Temperature Sensor Voltage is more than 4.9 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the water temperature sensor (for radiator outlet side) connector.



A

REPLACE WATER TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE)

B

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE))
5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the water temperature sensor (for radiator outlet side) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A15,A50)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A50)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Engine Coolant Temperature Sensor

A15-25 (WTR) or A50-1 (WTR) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the water temperature sensor (for radiator outlet side) connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR