Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D8A11  FC Inter Cooler Outlet Temperature Sensor Circuit Short to Ground  P1D8A15  FC Inter Cooler Outlet Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

The FC stack inlet air temperature sensor (vacuum sensor assembly) is provided on the intercooler outlet side, and is used to monitor air temperature cooled down by the intercooler. The FC stack inlet air temperature sensor (vacuum sensor assembly) has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the EV control ECU as voltage changes.

The FC stack inlet air temperature sensor (vacuum sensor assembly) is connected to the EV control ECU, and a power voltage of 5 V is supplied from the ICT terminal of the EV control ECU to the sensor via resistor R. Since resistor R and the sensor are connected in series, resistance varies as an intake air temperature changes, and potential of the ICT terminal also varies.

A283580E11
3.354,2.271 3.74,1.99 false 3.292,4.271 4.167,4.5 0.875,0.229 10 false Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 false (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 false 30 2.281,1.583 2.521,1.802 0.24,0.219 10 false 10 2.354,1.875 2.594,2.094 0.24,0.219 10 false 5 2.354,2.094 2.594,2.313 0.24,0.219 10 false 3 2.354,2.26 2.51,2.479 0.156,0.219 10 false 2 2.344,2.531 2.594,2.75 0.25,0.219 10 false 1 2.24,2.833 2.479,3.052 0.24,0.219 10 false 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 false 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 false 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 false 20 2.542,3.823 2.781,4.042 0.24,0.219 10 false -20 2.938,3.823 3.177,4.042 0.24,0.219 10 false 0 3.208,3.823 3.448,4.042 0.24,0.219 10 false 20 3.521,3.823 3.76,4.042 0.24,0.219 10 false 40 3.833,3.823 4.073,4.042 0.24,0.219 10 false 60 4.146,3.823 4.385,4.042 0.24,0.219 10 false 80 4.385,3.823 4.625,4.042 0.24,0.219 10 false 100 2.583,4 2.823,4.219 0.24,0.219 10 false -4 2.896,4 3.135,4.219 0.24,0.219 10 false 32 3.208,4 3.448,4.219 0.24,0.219 10 false 68 3.479,4 3.729,4.25 0.25,0.25 10 false 104 3.792,4 4.125,4.25 0.333,0.25 10 false 140 4.094,4 4.417,4.25 0.323,0.25 10 false 176 4.385,4 4.708,4.25 0.323,0.25 10 false 212 4.677,3.823 5,4.073 0.323,0.25 10 false (°C) 4.677,4 5,4.25 0.323,0.25 10 false (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 false Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 false Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 false 0.3

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D8A11 FC Inter Cooler Outlet Temperature Sensor Circuit Short to Ground If the +B voltage is not low when the ignition switch is turned to ON, the output voltage of the FC stack inlet air temperature sensor (vacuum sensor assembly) circuit remains at less than 0.1 V for more than 3 seconds.
(1 trip detection logic)
·

FC stack inlet air temperature sensor (vacuum sensor assembly)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A
P1D8A15 FC Inter Cooler Outlet Temperature Sensor Circuit Short to Battery or Open If all of the following conditions are met, and the output voltage of the FC stack inlet air temperature sensor (vacuum sensor assembly) circuit remains at more than 4.825 V for more than 3 seconds.
·

FC Mode is in FC Startup Process or FC Working

·

Intake air temperature is more than 20°C (68°F)

·

Mass air flow meter sub-assembly is normal

·

+B voltage is not low


(1 trip detection logic)
·

FC stack inlet air temperature sensor (vacuum sensor assembly)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A

Detection timing: P1D8A11
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Detection timing: P1D8A15
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ ○ ○ ○ -

HINT:

By accessing the "FC Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1D8A11
·

FC Inter Cooler Outlet Temperature Sensor Voltage

·

FC Inter Cooler Outlet Temperature


P1D8A15

WIRING DIAGRAM

A335331E19
4.583,1.354 4.979,1.531 0.396,0.177 10 false ICT 2.146,1.969 2.542,2.146 0.396,0.177 10 false E2 4.354,1.365 4.656,1.542 0.302,0.177 10 false 25 2.406,1.958 2.708,2.135 0.302,0.177 10 false 2 2.406,1.354 2.708,1.531 0.302,0.177 10 false 4 4.365,1.958 4.667,2.135 0.302,0.177 10 false 22 4.583,1.948 4.979,2.125 0.396,0.177 10 false GIC2 5.74,0.938 6.042,1.115 0.302,0.177 10 false 5 V 5,2.969 5.479,3.135 0.479,0.167 10 false G14*1 5.021,3.156 6.385,3.531 1.365,0.375 10 false EV Control ECU 0.406,2.625 0.708,2.802 0.302,0.177 10 false B13 0.417,2.802 2.854,3.438 2.438,0.635 10 false FC Stack Inlet Air Temperature Sensor (Vacuum Sensor Assembly) 2.031,1.365 2.427,1.542 0.396,0.177 10 false THA 5.448,2.969 5.927,3.135 0.479,0.167 10 false A14*2 3.177,3.052 4.188,3.24 1.01,0.188 10 false *1: for LHD 3.177,3.365 4.188,3.552 1.01,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

P1D8A11
1.

Turn the ignition switch to ON and wait for 3 seconds or more.


P1D8A15
1.

Wait for at least 3 seconds with the shift state in park (P), the ignition switch to ON (READY), and the "FC Work Mode" in Working or Startup Process. Perform a check with the "Intake Air Temperature (Filtered Value)" is more than 20°C (68°F).



PROCEDURE

1.READ VALUE USING GTS (FC INTER COOLER OUTLET TEMPERATURE SENSOR VOLTAGE)
a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
FC Inter Cooler Outlet Temperature Sensor Voltage
50003 397 1034
Result:
Result Proceed to
The value of FC Inter Cooler Outlet Temperature Sensor Voltage is more than 4.825 V A
The value of FC Inter Cooler Outlet Temperature Sensor Voltage is less than 0.10 V B


HINT:
·

If there is an open circuit, the GTS indicates more than 4.825 V.

·

If there is a short circuit, the GTS indicates less than 0.10 V.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Pre-procedure1

a.
A476952

Disconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


b.
A358782C09
0.323,3.375 0.76,3.729 0.438,0.354 1.135,4.302 1.51,3.615 true 2.448,4.333 2.198,3.604 true 0.729,1.521 1.042,1.677 0.313,0.156 10 false *1 2.635,1.531 2.948,1.688 0.313,0.156 10 false *2 0.229,2.542 0.542,2.698 0.313,0.156 10 false *a 0.427,3.469 0.74,3.625 0.313,0.156 10 false B13 1.031,4.344 1.344,4.5 0.313,0.156 10 false E2 2.375,4.344 2.75,4.563 0.375,0.219 10 false THA
*1 FC Stack Inlet Air Temperature Sensor (Vacuum Sensor Assembly)
*2 EV Control ECU
*a Front view of wire harness connector
(to FC Stack Inlet Air Temperature Sensor (Vacuum Sensor Assembly))


Connect terminals 4 (THA) and 2 (E2) of the FC stack inlet air temperature sensor (vacuum sensor assembly) connector on the wire harness side.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
FC Inter Cooler Outlet Temperature Sensor Voltage
50003 397 1034

Result:
Result Proceed to
The value of FC Inter Cooler Outlet Temperature Sensor Voltage is less than 0.10 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.



A

REPLACE FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY)

B

3.CONFIRM MODEL
3.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))

B

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))
4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,B13)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(B13)Engine Compartment>No. 2 Stack Wire>Vacuum Sensor Assembly

G14-25 (ICT) - B13-4 (THA) Always Below 1 Ω
G14-22 (GIC2) - B13-2 (E2) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,B13)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B13)Engine Compartment>No. 2 Stack Wire>Vacuum Sensor Assembly

A14-25 (ICT) - B13-4 (THA) Always Below 1 Ω
A14-22 (GIC2) - B13-2 (E2) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

Pre-procedure1

a.
A476952

Disconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


Procedure1

a.
A335356C05
0.708,0.448 1.021,0.646 0.313,0.198 10 false *1 2.625,0.302 2.938,0.5 0.313,0.198 10 false *2
*1 FC Stack Inlet Air Temperature Sensor (Vacuum Sensor Assembly)
*2 EV Control ECU


Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
FC Inter Cooler Outlet Temperature Sensor Voltage
50003 397 1034

Result:
Result Proceed to
The value of FC Inter Cooler Outlet Temperature Sensor Voltage is more than 4.825 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.



A

REPLACE FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY)

B

7.CONFIRM MODEL
7.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))

B

9.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))
8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,B13)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(B13)Engine Compartment>No. 2 Stack Wire>Vacuum Sensor Assembly

G14-25 (ICT) or B13-4 (THA) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.


b.

Reconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR TEMPERATURE SENSOR (VACUUM SENSOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,B13)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B13)Engine Compartment>No. 2 Stack Wire>Vacuum Sensor Assembly

A14-25 (ICT) or B13-4 (THA) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.


b.

Reconnect the FC stack inlet air temperature sensor (vacuum sensor assembly) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR