Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D9011  FC Stack Inlet Pressure Sensor Circuit Short to Ground  P1D9015  FC Stack Inlet Pressure Sensor Circuit Short to Battery or Open  


DESCRIPTION

Air that flows into the FC stack is compressed by the FC air compressor with motor assembly, and then cooled down by the intercooler. The FC stack inlet air pressure sensor (vacuum sensor assembly) monitors pressure of the air, and converts it into a voltage.

The FC stack inlet air pressure sensor (vacuum sensor assembly) measures pressure of the air flowing into the FC stack as absolute pressure, thus, it can measure the FC stack inlet air pressure without influence from changes in the atmospheric pressure due to altitude, etc.

A327839E10
0.104,0.083 0.948,0.323 0.844,0.24 10 false Voltage (V) 0.24,0.74 1.01,0.938 0.771,0.198 10 false 4.5 0.25,1.563 1.021,1.76 0.771,0.198 10 false 2.0 0.25,2.01 1.021,2.208 0.771,0.198 10 false 1.0 2.823,2.542 3.427,2.844 0.604,0.302 10 false kPa(abs) 2.854,3.042 3.427,3.354 0.573,0.313 10 false psi(abs) 0.854,2.563 1.302,2.771 0.448,0.208 10 false 13.30 1.469,2.552 1.917,2.76 0.448,0.208 10 false 96.15 2.385,2.542 2.958,2.76 0.573,0.219 10 false 303.30 0.865,3.042 1.219,3.271 0.354,0.229 10 false 1.93 1.448,3.052 1.948,3.281 0.5,0.229 10 false 13.94 2.469,3.052 2.99,3.323 0.521,0.271 10 false 43.98

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D9011 FC Stack Inlet Pressure Sensor Circuit Short to Ground If the +B voltage is not low when the ignition switch is turned to ON, the output voltage of the FC stack inlet air pressure sensor (vacuum sensor assembly) circuit remains at less than 0.60 V for more than 3 seconds.
(1 trip detection logic)
·

FC stack inlet air pressure sensor (vacuum sensor assembly)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A
P1D9015 FC Stack Inlet Pressure Sensor Circuit Short to Battery or Open If the +B voltage is not low when the ignition switch is turned to ON, the output voltage of the FC stack inlet air pressure sensor (vacuum sensor assembly) circuit remains at more than 4.85 V for more than 3 seconds.
(1 trip detection logic)
·

FC stack inlet air pressure sensor (vacuum sensor assembly)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1D9011 FC Inter Cooler Outlet Pressure Sensor Voltage
P1D9015

HINT:

If DTCs are found, read the "FC Inter Cooler Outlet Pressure Sensor Voltage" in the Data List on a GTS.


FC Inter Cooler Outlet Pressure Sensor Voltage Malfunction
Less than 0.60 V
·

Open in VICP (5 V power supply) circuit

·

Short in ICP circuit to ground

·

Short in ICP circuit to GIC2 (GND) circuit


Higher than 4.85 V
·

Short in VICP circuit to ICP circuit

·

Open in ICP circuit

·

Open in GIC2 (GND) circuit



HINT:

It is suspected that malfunctions, or open/short circuits have occurred in the FC stack inlet air pressure sensor (vacuum sensor assembly).


WIRING DIAGRAM

A477029E02
4.802,3.125 5.26,3.323 0.458,0.198 10 false G14*1 0.146,3.448 1.927,3.708 1.781,0.26 10 false *3: Shield Ground 4.75,1.99 5.208,2.188 0.458,0.198 10 false GIC2 4.49,1.99 4.802,2.188 0.313,0.198 10 false 22 4.771,1.469 5.219,1.677 0.448,0.208 10 false ICP 4.5,1.479 4.958,1.677 0.458,0.198 10 false 23 4.781,0.885 5.396,1.083 0.615,0.198 10 false VICP 4.5,0.885 4.813,1.083 0.313,0.198 10 false 24 1.094,2.479 1.552,2.677 0.458,0.198 10 false B13 1.094,2.646 3.302,3.104 2.208,0.458 10 false FC Stack Inlet Air Pressure Sensor (Vacuum Sensor Assembly) 2.875,1.979 3.031,2.177 0.156,0.198 10 false 2 2.583,2.094 3.042,2.292 0.458,0.198 10 false E2 2.885,1.469 3.042,1.667 0.156,0.198 10 false 1 2.5,1.573 2.813,1.771 0.313,0.198 10 false PIM 2.875,0.906 3.063,1.146 0.188,0.24 10 false 3 2.563,1 2.906,1.198 0.344,0.198 10 false VC 5.479,0.615 5.938,0.813 0.458,0.198 10 false 5 V 4.49,2.385 4.802,2.583 0.313,0.198 10 false 32 4.76,2.385 5.219,2.583 0.458,0.198 10 false DRN6 3.885,2.365 4.344,2.563 0.458,0.198 10 false *3 4.813,3.292 6.125,3.552 1.313,0.26 10 false EV Control ECU 5.26,3.135 5.719,3.333 0.458,0.198 10 false A14*2 0.125,2.792 1.906,3.052 1.781,0.26 10 false *1: for LHD 0.146,3.135 1.927,3.396 1.781,0.26 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 5 seconds or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FC STACK INLET AIR PRESSURE SENSOR (VACUUM SENSOR ASSEMBLY))

Pre-procedure1

a.
A476952

Disconnect the FC stack inlet air pressure sensor (vacuum sensor assembly) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B13)Location & Routing

Click Connector(B13)Engine Compartment>No. 2 Stack Wire>Vacuum Sensor Assembly

B13-3 (VC) - B13-2 (E2) Ignition switch ON 4.75 to 5.25 V
B13-1 (PIM) - B13-2 (E2) Ignition switch ON 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC stack inlet air pressure sensor (vacuum sensor assembly) connector.



OK

2.REPLACE FC STACK INLET AIR PRESSURE SENSOR (VACUUM SENSOR ASSEMBLY)

NG

5.CONFIRM MODEL
2.REPLACE FC STACK INLET AIR PRESSURE SENSOR (VACUUM SENSOR ASSEMBLY)
HINT:

Click hereEngine / Hybrid System>FC CONTROL>PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 5 seconds or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1D9011 or P1D9015 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

END

5.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR PRESSURE SENSOR (VACUUM SENSOR ASSEMBLY))

B

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR PRESSURE SENSOR (VACUUM SENSOR ASSEMBLY))
6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR PRESSURE SENSOR (VACUUM SENSOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC stack inlet air pressure sensor (vacuum sensor assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,B13)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(B13)Engine Compartment>No. 2 Stack Wire>Vacuum Sensor Assembly

G14-23 (ICP) - B13-1 (PIM) Always Below 1 Ω
G14-22 (GIC2) - B13-2 (E2) Always Below 1 Ω
G14-24 (VICP) - B13-3 (VC) Always Below 1 Ω
G14-23 (ICP) or B13-1 (PIM) - Body ground and other terminals Always 10 kΩ or higher
G14-24 (VICP) or B13-3 (VC) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.


b.

Reconnect the FC stack inlet air pressure sensor (vacuum sensor assembly) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC STACK INLET AIR PRESSURE SENSOR (VACUUM SENSOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC stack inlet air pressure sensor (vacuum sensor assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,B13)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B13)Engine Compartment>No. 2 Stack Wire>Vacuum Sensor Assembly

A14-23 (ICP) - B13-1 (PIM) Always Below 1 Ω
A14-22 (GIC2) - B13-2 (E2) Always Below 1 Ω
A14-24 (VICP) - B13-3 (VC) Always Below 1 Ω
A14-23 (ICP) or B13-1 (PIM) - Body ground and other terminals Always 10 kΩ or higher
A14-24 (VICP) or B13-3 (VC) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.


b.

Reconnect the FC stack inlet air pressure sensor (vacuum sensor assembly) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR