Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DE511  Hydrogen Tank 1 Temperature Sensor Circuit Short to Ground  P1DE515  Hydrogen Tank 1 Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

The hydrogen tank temperature sensor is provided inside the tank valve sub-assembly of the No. 1 hydrogen tank assembly, and is used to detect hydrogen temperatures in the tank.

The resistance of the built-in thermistor of the hydrogen tank temperature sensor varies in accordance with variations in the tank internal hydrogen temperature. The lower the hydrogen temperature in the tank is, the greater the thermistor resistance becomes. On the contrary, the higher the temperature is, the smaller the resistance becomes.

Hydrogen temperatures in the tank are transmitted to the hydrogen fuel control ECU, and such information is used for corrections of the remaining amount of hydrogen as well as for the temperature control of the tank.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DE511 Hydrogen Tank 1 Temperature Sensor Circuit Short to Ground If the +B voltage is not low when the ignition switch is ON, the output voltage of the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) circuit remains at less than 0.1 V for more than 3 seconds.
(1 trip detection logic)
·

No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1)

·

Hydrogen fuel control ECU assembly

·

Wire harness or connector


Master Warning: Comes on Hydrogen Filling Control A
P1DE515 Hydrogen Tank 1 Temperature Sensor Circuit Short to Battery or Open If the +B voltage is not low when the ignition switch is ON, the output voltage of the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) circuit remains at more than 4.9 V for more than 3 seconds.
(1 trip detection logic)
·

No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1)

·

Hydrogen fuel control ECU assembly

·

Wire harness or connector


Master Warning: Comes on Hydrogen Filling Control A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ ○

Related Data List
DTC No. Data List
P1DE511 Hydrogen Tank 1 Temperature Sensor Voltage
P1DE515

WIRING DIAGRAM

A477011E03
0.604,3.219 2.594,3.417 1.99,0.198 10 false No. 1 Hydrogen Tank Assembly 0.604,3.063 2.594,3.26 1.99,0.198 10 false h1 2.844,1.333 3.354,1.531 0.51,0.198 10 false 1 2.844,1.927 3.25,2.188 0.406,0.26 10 false 3 4.979,1.333 5.49,1.531 0.51,0.198 10 false 29 4.969,1.927 5.479,2.125 0.51,0.198 10 false 28 4.771,2.948 5.281,3.146 0.51,0.198 10 false G4 4.771,3.125 7.135,3.438 2.365,0.313 10 false Hydrogen Fuel Control ECU Assembly 5.26,1.333 5.771,1.531 0.51,0.198 10 false TNT1 5.281,1.938 5.792,2.135 0.51,0.198 10 false GTT1 5.896,0.938 6.406,1.135 0.51,0.198 10 false 5 V 0.385,2.333 2.781,2.74 2.396,0.406 10 false Hydrogen Tank Temperature Sensor 1 2.5,1.323 3.01,1.521 0.51,0.198 10 false IB6 2.49,1.927 3,2.125 0.51,0.198 10 false IB7

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 1 minute or more.



PROCEDURE

1.READ VALUE USING GTS (HYDROGEN TANK 1 TEMPERATURE SENSOR VOLTAGE)
a.

Read the value displayed on the GTS.

Powertrain > Hydrogen Filling Control > Data List
Tester Display
Hydrogen Tank 1 Temperature Sensor Voltage
50003 494 26
Result:
Result Proceed to
The value of Hydrogen Tank 1 Temperature Sensor Voltage is more than 4.9 V A
The value of Hydrogen Tank 1 Temperature Sensor Voltage is less than 0.1 V B


HINT:
·

If there is an open circuit, the GTS indicates more than 4.9 V.

·

If there is a short circuit, the GTS indicates less than 0.1 V.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Pre-procedure1

a.
A476963

Disconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) connector.


b.
A335349C13
0.292,2.688 0.792,2.938 0.5,0.25 0.979,3.156 1.469,2.698 true 2.042,2.677 2.448,3.115 true 0.729,0.438 1.042,0.635 0.313,0.198 10 false *1 2.646,0.24 2.958,0.438 0.313,0.198 10 false *2 0.823,2.094 1.135,2.292 0.313,0.198 10 false *a 0.865,3.177 1.24,3.365 0.375,0.188 10 false IB6 2.417,3.156 2.792,3.354 0.375,0.198 10 false IB7 0.438,2.75 0.792,3.042 0.354,0.292 10 false h1
*1 No. 1 Hydrogen Tank Assembly (Hydrogen Tank Temperature Sensor 1)
*2 Hydrogen Fuel Control ECU Assembly
*a Front view of wire harness connector
(to No. 1 Hydrogen Tank Assembly (Hydrogen Tank Temperature Sensor 1))


Connect terminals 1 (IB6) and 3 (IB7) of the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) connector on the wire harness side.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > Hydrogen Filling Control > Data List
Tester Display
Hydrogen Tank 1 Temperature Sensor Voltage
50003 494 26

Result:
Result Proceed to
The value of Hydrogen Tank 1 Temperature Sensor Voltage is less than 0.1 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) connector.



A

REPLACE NO. 1 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 1)

B

3.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 1 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 1))
3.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 1 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 1))

Pre-procedure1

a.

Disconnect the hydrogen fuel control ECU assembly connector.


b.

Disconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G4,h1)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

Click Connector(h1)Body>Hydrogen Tank Valve Wire>No. 1 Hydrogen Tank Assembly

G4-29 (TNT1) - h1-1 (IB6) Always Below 1 Ω
G4-28 (GTT1) - h1-3 (IB7) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) connector.


b.

Reconnect the hydrogen fuel control ECU assembly connector.



OK

REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

Pre-procedure1

a.
A476963

Disconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) connector.


Procedure1

a.
A335356C06
0.729,0.469 1.042,0.667 0.313,0.198 10 false *1 2.615,0.292 2.927,0.49 0.313,0.198 10 false *2
*1 No. 1 Hydrogen Tank Assembly (Hydrogen Tank Temperature Sensor 1)
*2 Hydrogen Fuel Control ECU Assembly


Read the value displayed on the GTS.

Powertrain > Hydrogen Filling Control > Data List
Tester Display
Hydrogen Tank 1 Temperature Sensor Voltage
50003 494 26

Result:
Result Proceed to
The value of Hydrogen Tank 1 Temperature Sensor Voltage is more than 4.9 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor 1) connector.



A

REPLACE NO. 1 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 1)

B

5.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 1 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 1))
5.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 1 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 1))

Pre-procedure1

a.

Disconnect the hydrogen fuel control ECU assembly connector.


b.

Disconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G4,h1)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

Click Connector(h1)Body>Hydrogen Tank Valve Wire>No. 1 Hydrogen Tank Assembly

G4-29 (TNT1) or h1-1 (IB6) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 1 hydrogen tank assembly (hydrogen tank temperature sensor) connector.


b.

Reconnect the hydrogen fuel control ECU assembly connector.



OK

REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR