Home › Engine / Hybrid System › FUEL › HYDROGEN FUEL CONTROL ECU
RM37H0E _51 Engine / Hybrid System _097300 FUEL _0455433 HYDROGEN FUEL CONTROL ECU A

FUEL  HYDROGEN FUEL CONTROL ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A477870N02
6.448,0.708 6.781,0.708 false 6.5,0.281 6.833,0.281 false 1.917,1.24 2.156,1 2.156,1 2.323,1 true 5.521,0.927 5.688,0.927 5.688,0.927 5.76,1.458 true 5.271,2.854 5.438,2.854 5.438,2.854 5.688,3.333 true 4.146,2.833 4.25,2.833 4.25,2.833 4.302,3.031 true 5.865,2.344 6.031,2.344 6.031,2.344 6.417,2.552 true 3.208,0.604 3.375,0.604 3.375,0.604 3.708,0.781 true 6.271,0.167 6.521,0.5 0.25,0.333 18 false 1 6.271,0.583 6.521,0.917 0.25,0.333 18 false 2 2.396,0.885 2.646,1.219 0.25,0.333 18 false 3 5.281,0.823 5.531,1.156 0.25,0.333 18 false 7 5.24,1.771 5.594,2.01 0.354,0.24 10 false x 2 5.063,2.74 5.313,3.073 0.25,0.333 18 false 4 3.917,2.708 4.167,3.042 0.25,0.333 18 false 5 5.625,2.229 5.875,2.563 0.25,0.333 18 false 6 2.969,0.563 3.219,0.896 0.25,0.333 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 BENCH TYPE REAR SEATBACK ASSEMBLY 67918F - - -
4 INSIDE REAR DOOR SCUFF PLATE LH 62332A - - -
5 REAR DOOR OPENING TRIM WEATHERSTRIP LH 62552F (Click here) - -
6 REAR SEAT SIDE GARNISH LH 64273D - - -
7 HYDROGEN FUEL CONTROL ECU ASSEMBLY 898C0 (Click here) - -

*1 NO. 1 ROOM PARTITION PAD - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the hydrogen fuel control ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effects/Inoperative when not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·
Learning completes when vehicle is driven
Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedure Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY

Hide 67918F 4.REMOVE REAR DOOR SCUFF PLATE INSIDE LH

Hide 62332A 5.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Z101186

HINT:

Pull back the rear door opening trim weatherstrip LH so that the rear seat side garnish LH can be removed.

Click here(Click here)



Hide 62552F 6.REMOVE REAR SEAT SIDE GARNISH LH

Hide 898C0 7.REMOVE HYDROGEN FUEL CONTROL ECU ASSEMBLY

a.
E454194C01
0,0 0,0 false
V113147

Remove in this Direction - -



b.
A477871N01
0.281,0.073 0.563,0.427 0.281,0.354 18 false i 4.031,0.063 4.313,0.417 0.281,0.354 18 false ii

i.

Disconnect the 2 hydrogen fuel control ECU assembly connectors.


ii.

Remove the 2 nuts and the hydrogen fuel control ECU assembly.

NOTICE:

If the hydrogen fuel control ECU assembly dropped or subjected to a strong impact, replace it with a new one.