Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1E1996  Infrared Transmitter Component Internal Failure  


DESCRIPTION

The hydrogen fuel control transmitter is mounted on the receptacle bracket. The transmitter sends information such as the hydrogen tank capacity, tank internal hydrogen pressure and temperature to a hydrogen station through infrared communication channels (unidirectional communication).

The hydrogen fuel control ECU monitors accumulated actuation currents of the hydrogen fuel control transmitter to detect open circuits, and when the ignition switch becomes ON with the fuel lid open, the hydrogen fuel control ECU assembly stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E1996 Infrared Transmitter Component Internal Failure During infrared transmission (during fuel lid open judgment*), an open circuit is detected if the measured current is less than 170 mA continuously for a period of 6 seconds.
·

Hydrogen fuel control transmitter

·

Hydrogen fuel control ECU assembly

·

Wire harness or connector


Master Warning: Does not come on Hydrogen Filling Control A

*: If the fuel lid has remained open for more than 120 minutes, the hydrogen fuel control ECU will enter sleep mode, and the infrared signal transmission will also stop.

Related Data List
DTC No. Data List
P1E1996 -

HINT:

It is suspected that the hydrogen fuel control transmitter or hydrogen fuel control ECU is malfunctioning, there is an open or short in the circuit, or a short in the +B circuit.


WIRING DIAGRAM

A477027E02
1.531,0.99 2.146,1.188 0.615,0.198 10 false VSEO 1.625,2.073 2.042,2.271 0.417,0.198 10 false SEO 1.51,2.615 2.125,2.813 0.615,0.198 10 false GSEO 2.042,1 2.354,1.198 0.313,0.198 10 false 3 2.052,2.073 2.365,2.271 0.313,0.198 10 false 2 2.052,2.604 2.365,2.802 0.313,0.198 10 false 1 5.24,3.854 5.552,4.052 0.313,0.198 10 false G4 5.24,4.031 6.667,4.375 1.427,0.344 10 false Hydrogen Fuel Control ECU Assembly 3.031,2.583 3.188,2.781 0.156,0.198 10 false 4 3.75,1 3.906,1.198 0.156,0.198 10 false 1 3.031,2.073 3.177,2.271 0.146,0.198 10 false 3 3.052,0.979 3.208,1.177 0.156,0.198 10 false 1 3.75,2.083 3.906,2.281 0.156,0.198 10 false 3 3.75,2.615 3.906,2.813 0.156,0.198 10 false 4 5.073,2.063 5.24,2.271 0.167,0.208 10 false 7 5,2.594 5.219,2.792 0.219,0.198 10 false 23 5.063,0.99 5.219,1.188 0.156,0.198 10 false 9 3.01,3.156 3.323,3.354 0.313,0.198 10 false XG1 5.24,0.99 5.854,1.188 0.615,0.198 10 false VSEO 5.24,2.073 5.656,2.271 0.417,0.198 10 false SEO 5.24,2.604 5.854,2.802 0.615,0.198 10 false GSEO 0.583,3.24 1.073,3.531 0.49,0.292 10 false X1 3.01,3.344 3.927,3.76 0.917,0.417 10 false Hydrogen Fuel Control Wire 0.563,3.396 1.979,3.938 1.417,0.542 10 false Hydrogen Fuel Control Transmitter 5,3.104 5.313,3.302 0.313,0.198 10 false 24 5.26,3.115 5.875,3.313 0.615,0.198 10 false IDRN 0.188,4.469 1.563,4.667 1.375,0.198 10 false *: Shield Ground 4.438,3.115 4.75,3.313 0.313,0.198 10 false * 6.302,0.927 6.76,1.125 0.458,0.198 10 false 5 V 6.063,1.583 6.521,1.781 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch off.

2.

Press the fuel lid opener switch.

3.

Fully open the fuel lid and wait for 10 seconds.

4.

With the fuel lid fully opened, turn the ignition switch to ON.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - HYDROGEN FUEL CONTROL TRANSMITTER)

Pre-procedure1

a.

Disconnect the hydrogen fuel control ECU assembly connector.


b.
A476961

Disconnect the hydrogen fuel control transmitter connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G4,X1)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

Click Connector(X1)Body>Hydrogen Fuel Control Wire>Hydrogen Fuel Control Transmitter

G4-9 (VSEO) - X1-3 (VSEO) Always Below 1 Ω
G4-7 (SEO) - X1-2 (SEO) Always Below 1 Ω
G4-23 (GSEO) - X1-1 (GSEO) Always Below 1 Ω
G4-9 (VSEO) or X1-3 (VSEO) - Body ground and other terminals Always 10 kΩ or higher
G4-7 (SEO) or X1-2 (SEO) - Body ground and other terminals Always 10 kΩ or higher



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G4)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

G4-9 (VSEO), G4-7 (SEO) or G4-23 (GSEO) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the hydrogen fuel control transmitter connector.


c.

Reconnect the hydrogen fuel control ECU assembly connector.



OK

2.REPLACE HYDROGEN FUEL CONTROL TRANSMITTER

NG

5.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - HYDROGEN FUEL CONTROL WIRE)
2.REPLACE HYDROGEN FUEL CONTROL TRANSMITTER

NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > Hydrogen Filling Control > Clear DTCs
50002 494
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch off.


b.

Press the fuel lid opener switch.


c.

Fully open the fuel lid and wait for 10 seconds.


d.

With the fuel lid fully opened, turn the ignition switch to ON.


Procedure1

a.

Check for DTCs.

Powertrain > Hydrogen Filling Control > Trouble Codes
50001 494
Result:
Result Proceed to
P1E1996 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY

B

END

5.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - HYDROGEN FUEL CONTROL WIRE)

Pre-procedure1

a.

Disconnect the hydrogen fuel control ECU assembly connector.


b.
A476962

Disconnect the hydrogen fuel control wire connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G4,XG1)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

Click Connector(XG1)Body>Hydrogen Fuel Control Wire>Hydrogen Fuel Control Wire and Floor Wire

G4-9 (VSEO) - XG1-1 Always Below 1 Ω
G4-7 (SEO) - XG1-3 Always Below 1 Ω
G4-23 (GSEO) - XG1-4 Always Below 1 Ω
G4-9 (VSEO) or XG1-1 - Body ground and other terminals Always 10 kΩ or higher
G4-7 (SEO) or XG1-3 - Body ground and other terminals Always 10 kΩ or higher



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G4)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

G4-9 (VSEO), G4-7 (SEO) or G4-23 (GSEO) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the hydrogen fuel control wire connector.


c.

Reconnect the hydrogen fuel control ECU assembly connector.



OK

REPLACE HYDROGEN FUEL CONTROL WIRE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR