Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0448067 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (for Single Type)

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Visually check the spiral cable sub-assembly for defects.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

B509941C04
2.135,0.708 2.469,0.885 0.333,0.177 0.521,5.083 0.813,5.292 0.292,0.208 2.698,1.958 2.969,2.135 0.271,0.177 5.698,0.552 5.969,0.729 0.271,0.177 0.833,1.677 1.104,1.854 0.271,0.177 2.49,4.948 2.833,5.156 0.344,0.208 5.979,3.635 6.302,3.813 0.323,0.177 0.76,4.802 1.26,5.063 true 2.104,6.292 2.104,5.375 true 0.76,4.583 1.26,4.844 true 1.479,6.26 1.479,5.25 1.479,5.25 2.083,4.99 true 2.24,4.865 2.594,4.635 true 2.229,5 2.594,4.833 true 1.49,4.323 2.083,4.75 true 1.885,6.115 1.885,5.333 1.885,5.333 2.094,5.24 true 2.24,5.24 2.552,5.521 true 6.26,4.063 6.51,3.802 true 5.771,4.51 6.021,4.25 true 5.75,3.781 6.021,4.052 true 1.698,5.833 1.708,5.292 1.708,5.292 2.073,5.104 true 2.25,4.75 2.594,4.406 true 2.24,5.115 2.563,5.281 true 2.24,5.385 2.469,5.75 true 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 2.229,0.729 2.594,0.927 0.365,0.198 10 false z8 0.573,5.125 0.865,5.281 0.292,0.156 10 false D31 2.802,1.979 2.958,2.177 0.156,0.198 10 false A 5.771,0.573 5.979,0.76 0.208,0.188 10 false z5 0.917,1.698 1.125,1.896 0.208,0.198 10 false z9 2.552,5 2.938,5.208 0.385,0.208 10 false D32 6.042,3.667 6.396,3.854 0.354,0.188 10 false D33 0.573,4.49 0.885,4.688 0.313,0.198 10 false D+ 0.563,4.719 0.875,4.917 0.313,0.198 10 false D- 2.021,6.344 2.333,6.542 0.313,0.198 10 false HO 1.375,6.302 1.833,6.5 0.458,0.198 10 false EAU 2.635,4.552 3.094,4.75 0.458,0.198 10 false +DP2 2.646,4.75 3.104,4.948 0.458,0.198 10 false +DP 1.188,4.24 1.646,4.438 0.458,0.198 10 false ECC 1.75,6.146 2.365,6.344 0.615,0.198 10 false DIST 2.615,5.479 3.073,5.677 0.458,0.198 10 false CCS 6.573,3.708 7.031,3.906 0.458,0.198 10 false EHT 5.635,4.542 6.094,4.74 0.458,0.198 10 false LIN 5.49,3.688 5.948,3.885 0.458,0.198 10 false BHT 1.583,5.865 2.042,6.063 0.458,0.198 10 false AU2 2.646,4.302 3.26,4.5 0.615,0.198 10 false ILL- 2.615,5.229 3.073,5.427 0.458,0.198 10 false AU1 2.396,5.792 3.01,5.99 0.615,0.198 10 false IL+2
*a Component without harness connected
(Spiral Cable Sub-assembly)
- -
V100144

Interlock - -


NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



i.

Set the spiral cable sub-assembly to the center position.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION



ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.


iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.


iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

·

Inspect the SRS airbag circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D31,z8)Location & Routing

Click Connector(D31)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z8)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assembly

D31-1 (D+) - z8-2 Always Below 1.3 Ω
D31-2 (D-) - z8-1 Always Below 1.3 Ω


·

Inspect the horn circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D32)Location & Routing

Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

D32-7 (HO) - A Always 3 Ω or less


·

Inspect the steering pad switch circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D32,z5)Location & Routing

Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z5)Instrument Panel>other>Spiral Cable Sub-Assembly , Steering Pad Switch Assembly

D32-4 (EAU) - z5-10 Always 3 Ω or less
D32-5 (AU2) - z5-9 Always 3 Ω or less
D32-9 (ILL-) - z5-6 Always 3 Ω or less
D32-10 (+DP2) - z5-5 Always 3 Ω or less
D32-11 (+DP) - z5-4 Always 3 Ω or less
D32-12 (AU1) - z5-3 Always 3 Ω or less
D32-14 (IL+2) - z5-1 Always 3 Ω or less


·

Inspect the cruise control circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D32,z5)Location & Routing

Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z5)Instrument Panel>other>Spiral Cable Sub-Assembly , Steering Pad Switch Assembly

D32-2 (ECC) - z5-12 Always 3 Ω or less
D32-6 (DIST) - z5-8 Always 3 Ω or less
D32-13 (CCS) - z5-2 Always 3 Ω or less


·

Inspect the steering heater circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D33,z9)Location & Routing

Click Connector(D33)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z9)Instrument Panel>other>Steering ECU (Steering Wheel Assembly) , Spiral Cable Sub-Assembly

D33-2 (EHT) - z9-1 Always Below 1.3 Ω
D33-3 (LIN) - z9-3 Always Below 1.3 Ω
D33-4 (BHT) - z9-4 Always Below 1.3 Ω





Hide 84306 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (for Dual Type)

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Visually check the spiral cable sub-assembly for defects.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

B522888C09
3.208,0.563 3.542,0.813 0.333,0.25 2.198,0.594 2.531,0.844 0.333,0.25 1.406,0.667 1.708,0.896 0.302,0.229 6.417,0.75 6.75,1 0.333,0.25 0.333,3.25 0.667,3.5 0.333,0.25 2.25,3.052 2.583,3.302 0.333,0.25 0.542,0.667 0.844,0.875 0.302,0.208 6.031,3.115 6.365,3.365 0.333,0.25 3.667,1.406 3.385,1.24 true 2.698,1.406 2.417,1.24 true 6.031,3.646 5.771,3.406 true 6.271,3.646 6.604,3.406 true 1.771,3.208 0.917,2.573 true 1.75,3 1.333,2.583 true 1.76,3.333 0.844,4.083 true 1.792,3.531 1.583,4.083 true 1.917,3.531 2,4.083 true 1.917,2.99 2.25,2.656 true 1.917,3.125 2.25,2.917 true 1.917,3.208 2.25,3.5 true 1.917,3.333 2.25,3.75 true 1.917,3.417 2.25,4 true 1.094,3.094 0.677,2.76 true 1.094,3.26 0.635,3.01 true 1.094,3.656 0.698,3.844 true 1.094,3.438 0.656,3.604 true 1.771,3.427 1.25,4.083 true 6.031,3.792 5.75,4.042 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 3.302,0.604 3.615,0.802 0.313,0.198 10 false z7 2.313,0.635 2.625,0.833 0.313,0.198 10 false z6 2.75,1.333 3.063,1.531 0.313,0.198 10 false *b 3.719,1.333 4.031,1.531 0.313,0.198 10 false *c 6.521,0.792 6.833,0.99 0.313,0.198 10 false z5 0.385,3.292 0.698,3.49 0.313,0.198 10 false D31 2.292,3.094 2.604,3.292 0.313,0.198 10 false D32 0.615,0.688 0.927,0.885 0.313,0.198 10 false z9 6.073,3.156 6.531,3.448 0.458,0.292 10 false D33 5.49,3.323 5.885,3.573 0.396,0.25 10 false BHT 6.646,3.323 7.135,3.646 0.49,0.323 10 false EHT 0.76,2.417 1.073,2.615 0.313,0.198 10 false EAU 1.177,2.417 1.49,2.615 0.313,0.198 10 false ECC 0.677,4.094 0.99,4.292 0.313,0.198 10 false AU2 1.083,4.094 1.396,4.292 0.313,0.198 10 false DIST 1.5,4.094 1.813,4.292 0.313,0.198 10 false HO 1.875,4.094 2.188,4.292 0.313,0.198 10 false IL+2 2.292,2.573 2.604,2.771 0.313,0.198 10 false ILL- 2.292,2.823 2.688,3 0.396,0.177 10 false +DP2 2.292,3.406 2.688,3.583 0.396,0.177 10 false +DP 2.292,3.667 2.688,3.844 0.396,0.177 10 false AU1 2.292,3.927 2.688,4.104 0.396,0.177 10 false CCS 0.448,2.677 0.76,2.875 0.313,0.198 10 false D+ 0.458,2.927 0.771,3.125 0.313,0.198 10 false D- 0.406,3.542 0.719,3.74 0.313,0.198 10 false D2- 0.406,3.771 0.719,3.969 0.313,0.198 10 false D2+ 1.51,0.698 1.823,0.896 0.313,0.198 10 false A 5.531,3.979 6.938,4.313 1.406,0.333 10 false LIN
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Color: Light Green
*c Color: Black - -
V100144

Interlock - -


NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



i.

Set the spiral cable sub-assembly to the center position.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION



ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.


iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.


iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

·

Inspect the SRS airbag circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D31,z6,z7)Location & Routing

Click Connector(D31)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z6)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assembly

Click Connector(z7)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assembly

D31-1 (D+) - z6-2 Always Below 1.3 Ω
D31-2 (D-) - z6-1 Always Below 1.3 Ω
D31-3 (D2-) - z7-1 Always Below 1.3 Ω
D31-4 (D2+) - z7-2 Always Below 1.3 Ω


·

Inspect the horn circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D32)Location & Routing

Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

D32-7 (HO) - A Always 3 Ω or less


·

Inspect the steering pad switch circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D32,z5)Location & Routing

Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z5)Instrument Panel>other>Spiral Cable Sub-Assembly , Steering Pad Switch Assembly

D32-4 (EAU) - z5-10 Always 3 Ω or less
D32-5 (AU2) - z5-9 Always 3 Ω or less
D32-9 (ILL-) - z5-6 Always 3 Ω or less
D32-10 (+DP2) - z5-5 Always 3 Ω or less
D32-11 (+DP) - z5-4 Always 3 Ω or less
D32-12 (AU1) - z5-3 Always 3 Ω or less
D32-14 (IL+2) - z5-1 Always 3 Ω or less


·

Inspect the cruise control circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D32,z5)Location & Routing

Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z5)Instrument Panel>other>Spiral Cable Sub-Assembly , Steering Pad Switch Assembly

D32-2 (ECC) - z5-12 Always 3 Ω or less
D32-6 (DIST) - z5-8 Always 3 Ω or less
D32-13 (CCS) - z5-2 Always 3 Ω or less


·

Inspect the steering heater circuit.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the spiral cable sub-assembly.

Click Location & Routing(D33,z9)Location & Routing

Click Connector(D33)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

Click Connector(z9)Instrument Panel>other>Steering ECU (Steering Wheel Assembly) , Spiral Cable Sub-Assembly

D33-2 (EHT) - z9-1 Always Below 1.3 Ω
D33-3 (LIN) - z9-3 Always Below 1.3 Ω
D33-4 (BHT) - z9-4 Always Below 1.3 Ω