Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for TOYOTA Connect) › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0484973 TELEMATICS SYSTEM(for TOYOTA Connect) C

TELEMATICS  TELEMATICS SYSTEM(for TOYOTA Connect)  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157213 Microphone Circuit Open Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telematics transceiver

·

Telephone microphone assembly

·

Harness or connector


Telematics A

WIRING DIAGRAM

E364325E56
1.406,0.823 1.969,1.031 0.563,0.208 10 false MCVD 1.469,1.271 1.906,1.479 0.438,0.208 10 false MCI+ 1.5,1.74 1.917,1.948 0.417,0.208 10 false MCI- 1.417,2.198 1.896,2.417 0.479,0.219 10 false SGND 1.896,0.833 2.25,1.042 0.354,0.208 10 false 5 1.896,1.271 2.323,1.49 0.427,0.219 10 false 6 1.896,1.74 2.208,1.979 0.313,0.24 10 false 7 1.896,2.198 2.25,2.417 0.354,0.219 10 false 23 0.49,2.771 0.948,2.979 0.458,0.208 10 false D68 0.479,2.958 3.135,3.302 2.656,0.344 10 false Telematics Transceiver 3.948,0.823 4.26,1.031 0.313,0.208 10 false 1 3.958,1.281 4.25,1.49 0.292,0.208 10 false 2 3.958,1.74 4.26,1.979 0.302,0.24 10 false 4 4.156,0.833 4.719,1.042 0.563,0.208 10 false MACC 4.156,1.281 4.719,1.49 0.563,0.208 10 false MCO+ 4.177,1.74 4.74,1.948 0.563,0.208 10 false MCO- 4.083,2.625 4.521,2.844 0.438,0.219 10 false H17 4.083,2.813 6.781,3.073 2.698,0.26 10 false Telephone Microphone Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

B

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)

Pre-procedure1

a.

Disconnect the D68 telematics transceiver connector.


b.

Disconnect the H17 telephone microphone assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68,H17)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D68-5 (MCVD) - H17-1 (MACC) Always Below 1 Ω
D68-6 (MCI+) - H17-2 (MCO+) Always Below 1 Ω
D68-7 (MCI-) - H17-4 (MCO-) Always Below 1 Ω
D68-23 (SGND) - Body ground Always 10 kΩ or higher
D68-5 (MCVD) - Body ground Always 10 kΩ or higher
D68-6 (MCI+) - Body ground Always 10 kΩ or higher
D68-7 (MCI-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK TELEMATICS TRANSCEIVER (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEMATICS TRANSCEIVER (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Remove the telephone microphone assembly but do not disconnect the connectors.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL



Procedure1

a.
E364326C28
1.5,0.219 1.885,0.448 0.385,0.229 2.458,1.844 2.198,1.333 true 1.083,1.823 1.458,1.375 true 1.583,0.26 1.885,0.438 0.302,0.177 10 false H17 0.198,0.167 0.427,0.354 0.229,0.188 10 false *a 2.292,1.865 2.708,2.021 0.417,0.156 10 false MACC 0.865,1.844 1.281,2 0.417,0.156 10 false MCO-
*a Component with harness connected
(Telephone Microphone Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H17)Location & Routing

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

H17-1 (MACC) - Body ground Ignition switch ON 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H17)Location & Routing

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

H17-4 (MCO-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

4.REPLACE TELEMATICS TRANSCEIVER
4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT