Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS TRANSCEIVER › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0448089 TELEMATICS TRANSCEIVER A

TELEMATICS  TELEMATICS TRANSCEIVER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E458297N01
0.094,1.344 4.417,3.719 4.323,2.375 1.948,3.219 2.229,3.479 2.229,3.479 2.552,3.479 false 1.167,1.708 1.458,1.708 1.458,1.708 1.74,1.969 false 0.688,2.292 0.979,2.292 0.979,2.292 1.188,2.656 false 2.51,2.24 2.688,1.802 2.688,1.802 2.958,1.802 false 1.042,0.438 1.323,0.438 1.323,0.438 1.604,0.646 false 6.458,0.198 6.75,0.198 false 5.896,1.875 5.896,2.323 false 4.417,3.219 4.708,3.219 false 5.823,2.375 6.031,2.719 0.208,0.344 18 false 2 3.031,1.656 3.24,1.938 0.208,0.281 18 false 6 4.76,3.052 4.969,3.323 0.208,0.271 18 false 4 0.729,2.979 1.042,3.177 0.313,0.198 10 false x 2 3.188,2.125 3.5,2.323 0.313,0.198 10 false x 2 4.031,2.427 4.281,2.625 0.25,0.198 10 false x 3 0.938,1.625 1.146,1.792 0.208,0.167 10 false *1 2.635,3.385 2.854,3.583 0.219,0.198 10 false *2 6.25,0.073 6.458,0.417 0.208,0.344 18 false 1 0.844,0.313 1.052,0.594 0.208,0.281 18 false 3 0.479,2.156 0.667,2.438 0.188,0.281 18 false 5 3.094,0.396 3.406,0.594 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 55403E - - -
3 NAVIGATION ECU ASSEMBLY WITH BRACKET - - - -
4 TELEMATICS TRANSCEIVER WITH BRACKET - - - -
5 NO. 1 INTEGRATION CONTROL BRACKET 84113H - - -
6 NO. 2 INTEGRATION CONTROL BRACKET 84113J - - -

*1 TELEMATICS TRANSCEIVER *2 INTEGRATION CONTROL SUB-ASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the telematics transceiver removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Telematics transceiver Register vehicle information Telematics System for eCall:
(Click here)
for TOYOTA Connect:
(Click here)
for TOYOTA Connect:

Code registration


See the Service Bulletin for the registration method.

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 55403E 2.REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 3.REMOVE NAVIGATION ECU ASSEMBLY WITH BRACKET

Hide 4.REMOVE TELEMATICS TRANSCEIVER WITH BRACKET

HINT:

The illustrations are representative examples, and details may differ.


a.
E458293


Hide 84113H 5.REMOVE NO. 1 INTEGRATION CONTROL BRACKET

HINT:

The illustrations are representative examples, and details may differ.


a.
E458295


Hide 84113J 6.REMOVE NO. 2 INTEGRATION CONTROL BRACKET

HINT:

The illustrations are representative examples, and details may differ.


a.
E458296