Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for TOYOTA Connect) › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0484973 TELEMATICS SYSTEM(for TOYOTA Connect) J

TELEMATICS  TELEMATICS SYSTEM(for TOYOTA Connect)  Received Voice Signal Circuit  


WIRING DIAGRAM

E284012E22
2.458,0.51 3.073,0.708 0.615,0.198 10 false 13 1.969,0.625 2.583,0.823 0.615,0.198 10 false VOR+ 1.979,1.448 2.594,1.646 0.615,0.198 10 false VOR- 4.833,0.646 5.448,0.844 0.615,0.198 10 false VOT+ 4.833,1.469 5.448,1.667 0.615,0.198 10 false VOT- 1.094,2 1.708,2.198 0.615,0.198 10 false D62 1.083,2.167 2.896,2.51 1.813,0.344 10 false Radio Receiver Assembly 2.469,1.344 2.76,1.542 0.292,0.198 10 false 14 4.531,1.354 4.823,1.552 0.292,0.198 10 false 33 4.531,0.521 4.823,0.719 0.292,0.198 10 false 17 4.688,2.01 5.302,2.208 0.615,0.198 10 false D68 4.698,2.177 6.948,2.469 2.25,0.292 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for TOYOTA Connect.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the D62 radio receiver assembly connector.


b.

Disconnect the D68 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D62,D68)Location & Routing

Click Connector(D62)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D62-13 (VOR+) - D68-17 (VOT+) Always Below 1 Ω
D62-14 (VOR-) - D68-33 (VOT-) Always Below 1 Ω
D62-13 (VOR+) - Body ground Always 10 kΩ or higher
D62-14 (VOR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TELEMATICS TRANSCEIVER
a.

Remove the telematics transceiver with the connectors still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.
E427042C08
1.469,0.583 1.917,0.885 0.448,0.302 0.823,2.042 1.073,3.094 1.073,3.094 1.25,3.094 true 0.792,1.948 0.969,1.229 0.969,1.229 1.135,1.229 true 1.188,1.146 2.052,1.427 0.865,0.281 10 false VOT+ (17) 1.313,3.021 1.958,3.271 0.646,0.25 10 false VOT- (33) 0.208,0.24 0.458,0.427 0.25,0.188 10 false *a 1.552,0.656 2.188,1.021 0.635,0.365 10 false D68
*a Component with harness connected
(Telematics Transceiver)


Check for pulses according to the value(s) in the table below.

Standard:
Tester Connection Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-17 (VOT+) - Body ground Calling while using the operator service A waveform synchronized with the sent voice is output
D68-33 (VOT-) - Body ground Calling while using the operator service A waveform synchronized with the sent voice is output



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG