Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for TOYOTA Connect) › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0484973 TELEMATICS SYSTEM(for TOYOTA Connect) C

TELEMATICS  TELEMATICS SYSTEM(for TOYOTA Connect)  B15DE87  Telematics Transceiver Location Data Missing Message  


DESCRIPTION

The telematics transceiver checks the reception condition of the location data every minute after the ignition switch is turned to ON. If the location data is not received from the navigation ECU assembly, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15DE87 Telematics Transceiver Location Data Missing Message Location information from USB communication is interrupted
·

Harness or connector

·

Telematics transceiver

·

Radio receiver assembly

·

Navigation ECU assembly


Telematics A

WIRING DIAGRAM

E427030E36
5.365,2.125 6.344,2.542 0.979,0.417 10 false Navigation ECU Assembly 5.385,3.719 6.354,4.135 0.969,0.417 10 false Radio Receiver Assembly 1.885,3.667 3.448,3.979 1.563,0.313 10 false Telematics Transceiver 0.979,4.313 3.021,4.552 2.042,0.24 10 false : USB Communication Line 2.583,2.76 3.198,2.958 0.615,0.198 10 false USBV 2.583,3.229 3.198,3.427 0.615,0.198 10 false USBG 5.438,2.781 6.052,2.979 0.615,0.198 10 false USBV 5.438,3.24 6.052,3.438 0.615,0.198 10 false USBG 5.396,3.531 5.75,3.729 0.354,0.198 10 false D62 5.354,1.958 5.906,2.208 0.552,0.25 10 false D141 2.594,0.688 3.208,0.885 0.615,0.198 10 false USB+ 2.583,1.677 3.198,1.875 0.615,0.198 10 false USBS 2.625,1.177 3.24,1.375 0.615,0.198 10 false USB- 5.448,0.729 6.063,0.927 0.615,0.198 10 false USB+ 5.438,1.208 6.052,1.406 0.615,0.198 10 false USB- 5.438,1.677 6.052,1.875 0.615,0.198 10 false USBS 5.24,0.573 5.406,0.771 0.167,0.198 10 false 1 5.229,1.052 5.396,1.25 0.167,0.198 10 false 2 5.229,1.563 5.396,1.76 0.167,0.198 10 false 3 3.146,2.542 3.469,2.792 0.323,0.25 10 false 15 3.167,3.031 3.479,3.271 0.313,0.24 10 false 31 5.156,2.646 5.385,2.854 0.229,0.208 10 false 10 5.167,3.115 5.396,3.323 0.229,0.208 10 false 11 3.198,0.979 3.365,1.177 0.167,0.198 10 false 1 3.198,0.5 3.365,0.698 0.167,0.198 10 false 2 3.198,1.438 3.365,1.635 0.167,0.198 10 false 3 3.094,0.719 3.646,0.969 0.552,0.25 10 false D138 3.115,2.75 3.667,3 0.552,0.25 10 false D68 3.115,3.229 3.667,3.479 0.552,0.25 10 false D68 4.385,1.458 4.938,1.708 0.552,0.25 10 false * 0.365,3.917 1.698,4.26 1.333,0.344 10 false *: Shielded 3.073,1.177 3.625,1.427 0.552,0.25 10 false D138 3.073,1.646 3.625,1.896 0.552,0.25 10 false D138

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


Pre-procedure1

b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

B

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - RADIO RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - RADIO RECEIVER ASSEMBLY)

Pre-procedure1

a.

Disconnect the D62 radio receiver assembly connector.


b.

Disconnect the D68 telematics transceiver connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D62,D68)Location & Routing

Click Connector(D62)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D62-10 (USBV) - D68-15 (USBV) Always Below 1 Ω
D62-11 (USBG) - D68-31 (USBG) Always Below 1 Ω
D62-10 (USBV) or D68-15 (USBV) - Body ground Always 10 kΩ or higher
D62-11 (USBG) or D68-31 (USBG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK RADIO RECEIVER ASSEMBLY (USBV, USBG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO RECEIVER ASSEMBLY (USBV, USBG)

Pre-procedure1

a.

Disconnect the D68 telematics transceiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-15 (USBV) - D68-31 (USBG) Ignition switch ON 4.75 to 5.25 V



Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-31 (USBG) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU ASSEMBLY)

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the D138 telematics transceiver connector.


b.

Disconnect the D141 navigation ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D138,D141)Location & Routing

Click Connector(D138)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(D141)Instrument Panel>Instrument Panel Wire>Navigation ECU Assembly

D138-2 (USB+) - D141-1 (USB+) Always Below 1 Ω
D138-1 (USB-) - D141-2 (USB-) Always Below 1 Ω
D138-3 (USBS) - D141-3 (USBS) Always Below 1 Ω
D138-2 (USB+) - Body ground Always 10 kΩ or higher
D138-1 (USB-) - Body ground Always 10 kΩ or higher
D138-3 (USBS) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELEMATICS TRANSCEIVER

Pre-procedure1

a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

B