Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2021.08
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B427558E41
3.25,0.542 3.656,0.781 0.406,0.24 4.531,0.542 4.938,0.781 0.406,0.24 4.604,0.552 4.917,0.75 0.313,0.198 10 false D86 3.313,0.563 3.625,0.76 0.313,0.198 10 false G37

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
D86-18 (E) - Body ground - Ground Always Below 1 Ω -
D86-4 (+B) - D86-18 (E) Input Power supply Ignition switch off 11 to 14 V -
D86-15 (CUTB) - D86-18 (E) Input Dark current cut pin* Ignition switch off 11 to 14 V -

*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Reconnect the D86 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
D86-17 (IG1D) - D86-18 (E) Output IG power supply Ignition switch off → on (IG) Below 1 V → 10 V or higher
Power source control

IG Relay Monitor (Outside)


D86-16 (ACCD) - D86-18 (E) Output ACC power supply Ignition switch off → on (ACC) Below 1 V → 10 V or higher
Power source control

ACC Relay Monitor


G37-17 (CLG1) - D86-18 (E) Output Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
G37-17 (CLG1) - D86-18 (E) Input Input to driver door lock sensor
(front door outside handle assembly (for Driver Door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Driver door lock sensor touched


Pulse generation
(See waveform 3)
Entry&Start

D-Door Trigger Switch


G37-17 (CLG1) - D86-18 (E) Input Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor touched


Pulse generation
(See waveform 4)
Entry&Start

D-Door Touch Sensor


G37-16 (CG1B) - D86-18 (E) Output Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
G37-15 (CLG2) - D86-18 (E) Output Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
G37-15 (CLG2) - D86-18 (E) Input Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Front passenger door lock sensor touched


Pulse generation
(See waveform 3)
Entry&Start

P-Door Touch Sensor


G37-15 (CLG2) - D86-18 (E) Input Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor touched


Pulse generation
(See waveform 4)
Entry&Start

P-Door Touch Sensor


G37-14 (CG2B) - D86-18 (E) Output Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
G37-1 (CLG3) - D86-18 (E)*2 Output Output to rear door electrical key antenna (for driver side)
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
G37-1 (CLG3) - D86-18 (E)*2 Input Input to rear door lock sensor (for driver side)
(rear door outside handle assembly (for driver side) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Rear door (for driver side) lock sensor touched


Pulse generation
(See waveform 3)
Entry&Start

Dr-Door Touch Sensor


G37-1 (CLG3) - D86-18 (E)*2 Input Input to rear door unlock sensor (for driver side)
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door (for driver side) unlock sensor touched


Pulse generation
(See waveform 4)
Entry&Start

Dr-Door Touch Sensor


G37-2 (CG3B) - D86-18 (E)*2 Output Output to rear door (for driver side) electrical key antenna (terminal on opposite side of component from CLG3 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
G37-9 (CLG4) - D86-18 (E)*2 Output Output to rear door electrical key antenna (for front passenger side)
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
G37-9 (CLG4) - D86-18 (E)*2 Input Input to rear door lock sensor (for front passenger side)
(rear door outside handle assembly (for front passenger side) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Rear door (for front passenger side) lock sensor touched


Pulse generation
(See waveform 3)
Entry&Start

Pr-Door Trigger Switch


G37-9 (CLG4) - D86-18 (E)*2 Input Input to rear door unlock sensor (for front passenger side)
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door (for front passenger side) unlock sensor touched


Pulse generation
(See waveform 4)
Entry&Start

Pr-Door Touch Sensor


G37-8 (CG4B) - D86-18 (E)*2 Output Output to rear door (for front passenger side) electrical key antenna (terminal on opposite side of component from CLG4 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
G37-11 (CLG7) - D86-18 (E) Output Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) Procedure:
1.

Door is closed

2.

Ignition switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Driver door lock sensor touched


Pulse generation
(See waveform 7)
-
G37-10 (CG7B) - D86-18 (E) Output Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Door is closed

2.

Ignition switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Driver door lock sensor touched


Pulse generation
(See waveform 7)
-
G37-13 (CLG8) - D86-18 (E) Output Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage electrical key switch off → on


Pulse generation
(See waveform 8)
-
G37-12 (CG8B) - D86-18 (E) Output Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage electrical key switch off → on


Pulse generation
(See waveform 8)
-
G37-26 (TSW5) - D86-18 (E) Input Luggage electrical key switch signal input Luggage electrical key switch off → on Pulse generation
(See waveform 9)
Entry&Start

Tr/B-Door Unlock SW


G37-18 (RCO) - D86-18 (E) Output Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 10)
-
G37-19 (RDAM) - D86-18 (E) Input Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Proceed:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 11)
-
G37-20 (CSEL) - D86-18 (E) Output Communication channel switching circuit Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation -
G37-21 (ASEL) - D86-18 (E) Output Communication channel switching circuit Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly held and then luggage electrical key switch off → on


Below 1 V → 4.5 to 6 V -

*1: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

*2: w/ Rear Door Entry



e.

Using an oscilloscope, check waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B340872N01
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND

Waveform 1

Item Content
Tester Connection G37-17 (CLG1) - D86-18 (E)
G37-15 (CLG2) - D86-18 (E)
G37-1 (CLG3) - D86-18 (E)*1
G37-9 (CLG4) - D86-18 (E)*1
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*2)



*1: w/ Rear Door Entry

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



ii.
B340873N01
0.177,1.021 0.635,1.219 0.458,0.198 10 false GND

Waveform 2

Item Content
Tester Connection G37-17 (CLG1) - D86-18 (E)
G37-15 (CLG2) - D86-18 (E)
G37-1 (CLG3) - D86-18 (E)*1
G37-9 (CLG4) - D86-18 (E)*1
Tool Setting 5 V/DIV., 100 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*2)



*1: w/ Rear Door Entry

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



iii.
B340877C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 0.677,1.917 1.135,2.115 0.458,0.198 10 false *a 1.646,2 1.969,2.156 0.323,0.156 10 false *b 2.615,1.917 3.073,2.115 0.458,0.198 10 false *a
*a Lock sensor not touched
*b Lock sensor touched


Waveform 3

Item Content
Tester Connection G37-17 (CLG1) - D86-18 (E)
G37-15 (CLG2) - D86-18 (E)
G37-1 (CLG3) - D86-18 (E)*1
G37-9 (CLG4) - D86-18 (E)*1
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*2)

5.

Lock sensor not touched → touched



*1: w/ Rear Door Entry

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



iv.
B340879C02
0.177,1.052 0.635,1.25 0.458,0.198 10 false GND 0.344,1.906 0.802,2.104 0.458,0.198 10 false *a 2.115,1.906 2.573,2.104 0.458,0.198 10 false *a 1.229,1.969 1.667,2.167 0.438,0.198 10 false *b
*a Unlock sensor not touched
*b Unlock sensor touched


Waveform 4

Item Content
Tester Connection G37-17 (CLG1) - D86-18 (E)
G37-15 (CLG2) - D86-18 (E)
G37-1 (CLG3) - D86-18 (E)*
G37-9 (CLG4) - D86-18 (E)*
Tool Setting 5 V/DIV., 50 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Unlock sensor not touched → touched



*: w/ Rear Door Entry



v.
B367472N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Waveform 5

Item Content
Tester Connection G37-16 (CG1B) - D86-18 (E)
G37-14 (CG2B) - D86-18 (E)
G37-2 (CG3B) - D86-18 (E)*1
G37-8 (CG4B) - D86-18 (E)*1
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*2)



*1: w/ Rear Door Entry

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



vi.
B367473N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Waveform 6

Item Content
Tester Connection G37-16 (CG1B) - D86-18 (E)
G37-14 (CG2B) - D86-18 (E)
G37-2 (CG3B) - D86-18 (E)*1
G37-8 (CG4B) - D86-18 (E)*1
Tool Setting 5 V/DIV., 100 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*2)



*1: w/ Rear Door Entry

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



vii.
B340875C06
0.208,1.073 0.667,1.271 0.458,0.198 10 false GND 1.365,1.927 1.823,2.125 0.458,0.198 10 false *a 2.417,1.938 2.875,2.135 0.458,0.198 10 false *b
*a Driver door lock sensor not touched
*b Driver door lock sensor touched


Waveform 7

Item Content
Tester Connection G37-11 (CLG7) - D86-18 (E)
G37-10 (CG7B) - D86-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Door is closed

2.

Ignition switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Driver door lock sensor touched




viii.
B340876N01
0.177,1.042 0.635,1.24 0.458,0.198 10 false GND

Waveform 8

Item Content
Tester Connection G37-13 (CLG8) - D86-18 (E)
G37-12 (CG8B) - D86-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage electrical key switch off → on




ix.
B251023C09
1.333,0.49 1.99,0.125 1.99,0.125 2.208,0.125 false 1.99,0.135 1.74,0.51 false 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.25,0.031 2.427,0.208 0.177,0.177 10 false *a
*a Checking for switch on signal at short intervals


Waveform 9

Item Content
Tester Connection G37-26 (TSW5) - D86-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Luggage electrical key switch off → on


x.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Waveform 10

Item Content
Tester Connection G37-18 (RCO) - D86-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




xi.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Waveform 11

Item Content
Tester Connection G37-19 (RDAM) - D86-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed






CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C01
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
A-31 (BECU) - Body ground Input Auxiliary battery power supply (for CPU) Ignition switch off 11 to 14 V


c.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
4F-31 (BZR) - Body ground Output Wireless door lock buzzer output Active Test Wireless Buzzer on Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)
-
Active Test Wireless Buzzer off Below 1 V