Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2021.08
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A3  Open in Rear Door Electrical Antenna Circuit, Drivers Side  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the rear door outside handle assembly (for driver side) (electrical key antenna) at intervals of 0.25 seconds. For the rear door outside handle assembly (for driver side) (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the rear door at intervals of 0.25 seconds. DTC B27A3 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side) (electrical key antenna) (between terminals CLG3 and ANT1, or terminals CG3B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A3 Open in Rear Door Electrical Antenna Circuit, Drivers Side An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side) (CLG3 - ANT1, CG3B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Rear door outside handle assembly (for driver side)

·

Harness or connector


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for rear door (for driver side) -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A3 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B622646E01
1.302,0.75 1.917,0.948 0.615,0.198 10 false ANT1 1.302,1.896 1.917,2.094 0.615,0.198 10 false ANT2 1.771,1.917 1.927,2.115 0.156,0.198 10 false 4 1.76,0.75 1.917,0.948 0.156,0.198 10 false 6 4.927,0.865 5.24,1.063 0.313,0.198 10 false G37 4.99,0.635 5.302,0.833 0.313,0.198 10 false 1 5.01,1.813 5.323,2.01 0.313,0.198 10 false 2 5.302,0.75 5.917,0.948 0.615,0.198 10 false CLG3 5.302,1.896 5.917,2.094 0.615,0.198 10 false CG3B 5.833,1.385 6.146,1.583 0.313,0.198 10 false IC 0.479,2.521 1.469,2.75 0.99,0.229 10 false F14 0.49,2.677 2.792,3.385 2.302,0.708 10 false Rear Door Outside Handle Assembly (for Driver Side) 5.104,2.531 6.635,3.49 1.531,0.958 10 false Certification ECU (Smart Key ECU Assembly) 6.479,2.01 6.938,2.208 0.458,0.198 10 false D86 6.531,1.802 6.844,2 0.313,0.198 10 false 18 6.25,2 6.406,2.198 0.156,0.198 10 false E 4.927,2.01 5.24,2.208 0.313,0.198 10 false G37

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE))

Pre-procedure 1

a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F14 rear door outside handle assembly (for driver side) connector.


Procedure 1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,F14)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(F14)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

G37-1 (CLG3) - F14-6 (ANT1) Always Below 1 Ω
G37-2 (CG3B) - F14-4 (ANT2) Always Below 1 Ω



Post-procedure 1

d.

Reconnect the G37 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE))
B473188C46
3.26,0.573 3.667,0.802 0.406,0.229 4.5,0.583 4.906,0.813 0.406,0.229 4.25,2.292 3.938,1.292 true 3.531,2.281 3.813,1.302 true 5.635,2.167 5.208,1.479 true 0.177,0.125 0.469,0.323 0.292,0.198 10 false *a 3.333,0.604 3.708,0.792 0.375,0.188 10 false G37 4.583,0.615 4.885,0.813 0.302,0.198 10 false D86 4.125,2.427 4.594,2.625 0.469,0.198 10 false CLG3 3.344,2.417 3.823,2.594 0.479,0.177 10 false CG3B 5.656,2.177 5.865,2.375 0.208,0.198 10 false E 0.698,2.719 0.99,2.917 0.292,0.198 10 false *b 4.104,2.708 4.354,2.906 0.25,0.198 10 false *c 4.01,3.563 4.406,3.76 0.396,0.198 10 false GND 0.594,3.552 0.979,3.75 0.385,0.198 10 false GND 0.698,4.708 0.99,4.906 0.292,0.198 10 false *d 4.104,4.708 4.396,4.906 0.292,0.198 10 false *e 4,5.573 4.354,5.771 0.354,0.198 10 false GND 0.583,5.573 0.917,5.792 0.333,0.219 10 false GND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Waveform 2 *d Waveform 3
*e Waveform 4 - -


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G37,D86)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

G37-1 (CLG3) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation
(See waveform 2)
G37-2 (CG3B) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 3)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation
(See waveform 4)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)