Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2021.08
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the rear door LH only, but the entry lock function operates, the request code is being transmitted properly from the rear door LH. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU (smart key ECU assembly) and rear door outside handle assembly LH).

WIRING DIAGRAM

B622646E01
1.302,0.75 1.917,0.948 0.615,0.198 10 false ANT1 1.302,1.896 1.917,2.094 0.615,0.198 10 false ANT2 1.771,1.917 1.927,2.115 0.156,0.198 10 false 4 1.76,0.75 1.917,0.948 0.156,0.198 10 false 6 4.927,0.865 5.24,1.063 0.313,0.198 10 false G37 4.99,0.635 5.302,0.833 0.313,0.198 10 false 1 5.01,1.813 5.323,2.01 0.313,0.198 10 false 2 5.302,0.75 5.917,0.948 0.615,0.198 10 false CLG3 5.302,1.896 5.917,2.094 0.615,0.198 10 false CG3B 5.833,1.385 6.146,1.583 0.313,0.198 10 false IC 0.479,2.521 1.469,2.75 0.99,0.229 10 false F14 0.49,2.677 2.792,3.385 2.302,0.708 10 false Rear Door Outside Handle Assembly (for Driver Side) 5.104,2.531 6.635,3.49 1.531,0.958 10 false Certification ECU (Smart Key ECU Assembly) 6.479,2.01 6.938,2.208 0.458,0.198 10 false D86 6.531,1.802 6.844,2 0.313,0.198 10 false 18 6.25,2 6.406,2.198 0.156,0.198 10 false E 4.927,2.01 5.24,2.208 0.313,0.198 10 false G37

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RL-DOOR LOCK POS SW)

NG

2.READ VALUE USING GTS (RL-DOOR LOCK POS SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL-Door Lock Pos SW Rear door LH unlock detection switch signal ON or OFF ON: Rear door LH unlocked
OFF: Rear door LH locked
-
Body Electrical > Main Body > Data List
Tester Display
RL-Door Lock Pos SW
50003 123 52
OK:

The GTS display changes correctly in response to the lock/unlock operation of the rear door LH.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (DR-DOOR TOUCH SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

3.READ VALUE USING GTS (DR-DOOR TOUCH SENSOR)
a.
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Turn the ignition switch off.


b.

Open and close the rear door LH.


c.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


d.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


e.

Check that the LED of the electrical key transmitter sub-assembly blinks.


f.

Read the Data List according to the display on the GTS.


g.

Touch the unlock sensor on the backside of the rear door outside handle assembly LH.

HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Dr-Door Touch Sensor Rear door LH touch sensor (unlock sensor) ON or OFF ON: Rear door LH touch sensor (unlock sensor) touched
OFF: Rear door LH touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Dr-Door Touch Sensor
50003 125 10
OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F14 rear door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,F14)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(F14)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

G37-1 (CLG3) - F14-6 (ANT1) Always Below 1 Ω
G37-2 (CG3B) - F14-4 (ANT2) Always Below 1 Ω
G37-1 (CLG3) or F14-6 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
G37-2 (CG3B) or F14-4 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the F14 rear door outside handle assembly LH connector.


e.

Reconnect the G37 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK REAR DOOR OUTSIDE HANDLE ASSEMBLY LH (INPUT TO REAR DOOR LH UNLOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK REAR DOOR OUTSIDE HANDLE ASSEMBLY LH (INPUT TO REAR DOOR LH UNLOCK SENSOR)
B443084C39
3.25,0.417 3.667,0.667 0.417,0.25 4.5,0.417 4.917,0.667 0.417,0.25 5.417,2.167 5.188,1.385 true 4.146,2.365 3.885,1.167 true 0.146,0.188 0.458,0.344 0.313,0.156 10 false *a 1.073,2.792 1.385,2.948 0.313,0.156 10 false *b 0.906,4.375 1.219,4.531 0.313,0.156 10 false *c 1.625,4.469 1.938,4.625 0.313,0.156 10 false *d 2.375,4.406 2.688,4.563 0.313,0.156 10 false *c 0.74,3.708 1.25,3.885 0.51,0.177 10 false GND 4.167,2.406 4.771,2.698 0.604,0.292 10 false CLG3 5.396,2.219 5.708,2.375 0.313,0.156 10 false E 3.323,0.448 3.667,0.625 0.344,0.177 10 false G37 4.594,0.458 4.906,0.615 0.313,0.156 10 false D86
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Unlock sensor not touched *d Unlock sensor touched


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G37,D86)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

G37-1 (CLG3) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door LH unlock sensor touched


5 V/DIV., 50 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH