If the entry unlock function does not operate for the rear door RH only, but the entry lock function operates, the request code is being transmitted properly from the rear door RH. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU (smart key ECU assembly) and rear door outside handle assembly RH).
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and system (for Entry Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR-Door Lock Pos SW | Rear door RH unlock detection switch signal | ON or OFF | ON: Rear door RH unlocked
OFF: Rear door RH locked |
- |
| Tester Display |
|---|
| RR-Door Lock Pos SW |
The GTS display changes correctly in response to the lock/unlock operation of the rear door RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Unlock Sensor (Backside) |
The illustrations shown are examples only.
Turn the ignition switch off.
Open and close the rear door RH.
With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door RH.
Check that the LED of the electrical key transmitter sub-assembly blinks.
Read the Data List according to the display on the GTS.
Touch the unlock sensor on the backside of the rear door outside handle assembly RH.
When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Pr-Door Touch Sensor | Rear door RH touch sensor (unlock sensor) | ON or OFF | ON: Rear door RH touch sensor (unlock sensor) touched
OFF: Rear door RH touch sensor (unlock sensor) not touched |
·
Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate. |
| Tester Display |
|---|
| Pr-Door Touch Sensor |
The GTS display changes correctly in response to the operation of the front door outside handle assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G37 certification ECU (smart key ECU assembly) connector.
Disconnect the F3 rear door outside handle assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G37,F3)Location & Routingewd_type=routing;type=c,c;code=G37,F3 Click Connector(G37)Instrument Panel>Floor Wire>Certification ECUewd_type=component;type=c;code=G37;pinno=9,8 Click Connector(F3)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly RHewd_type=component;type=c;code=F3;pinno=6,4 |
||
| G37-9 (CLG4) - F3-6 (ANT1) | Always | Below 1 Ω |
| G37-8 (CG4B) - F3-4 (ANT2) | Always | Below 1 Ω |
| G37-9 (CLG4) or F3-6 (ANT1) - Other terminals and body ground | Always | 10 kΩ or higher |
| G37-8(CG4B) or F3-4 (ANT2) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the F3 rear door outside handle assembly RH connector.
Reconnect the G37 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform 1 |
| *c | Unlock sensor not touched | *d | Unlock sensor touched |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
|
Click Location & Routing(G37,D86)Location & Routingewd_type=routing;type=c,c;code=G37,D86 Click Connector(G37)Instrument Panel>Floor Wire>Certification ECUewd_type=component;type=c;code=G37;pinno=9 Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECUewd_type=component;type=c;code=D86;pinno=18 |
|||
| G37-9 (CLG4) - D86-18 (E) | Procedure:
1.
Ignition switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not near the vehicle 5.
Rear door RH unlock sensor touched |
5 V/DIV., 50 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG