Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2021.08
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the rear door LH only, the request code may not be being transmitted from the rear door LH or the rear door outside handle assembly LH (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and rear door outside handle assembly LH (electrical key antenna)), or there may be wave interference.

WIRING DIAGRAM

B622646E01
1.302,0.75 1.917,0.948 0.615,0.198 10 false ANT1 1.302,1.896 1.917,2.094 0.615,0.198 10 false ANT2 1.771,1.917 1.927,2.115 0.156,0.198 10 false 4 1.76,0.75 1.917,0.948 0.156,0.198 10 false 6 4.927,0.865 5.24,1.063 0.313,0.198 10 false G37 4.99,0.635 5.302,0.833 0.313,0.198 10 false 1 5.01,1.813 5.323,2.01 0.313,0.198 10 false 2 5.302,0.75 5.917,0.948 0.615,0.198 10 false CLG3 5.302,1.896 5.917,2.094 0.615,0.198 10 false CG3B 5.833,1.385 6.146,1.583 0.313,0.198 10 false IC 0.479,2.521 1.469,2.75 0.99,0.229 10 false F14 0.49,2.677 2.792,3.385 2.302,0.708 10 false Rear Door Outside Handle Assembly (for Driver Side) 5.104,2.531 6.635,3.49 1.531,0.958 10 false Certification ECU (Smart Key ECU Assembly) 6.479,2.01 6.938,2.208 0.458,0.198 10 false D86 6.531,1.802 6.844,2 0.313,0.198 10 false 18 6.25,2 6.406,2.198 0.156,0.198 10 false E 4.927,2.01 5.24,2.208 0.313,0.198 10 false G37

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



HINT:
·

If the rear door LH entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52

PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK WAVE ENVIRONMENT

B

3.CHECK WAVE ENVIRONMENT
a.
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Subassembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the rear door outside handle assembly LH and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear door outside handle assembly LH.

·

When the electrical key transmitter sub-assembly is brought near the rear door outside handle assembly LH, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively. (w/o Double Locking System)




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

4.READ VALUE USING GTS (DR-DOOR TOUCH SENSOR)

B

AFFECTED BY WAVE INTERFERENCE

4.READ VALUE USING GTS (DR-DOOR TOUCH SENSOR)
a.
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Turn the ignition switch off.


b.

Open and close the rear door LH.


c.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


d.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


e.

Check that the LED of the electrical key transmitter sub-assembly blinks.


f.

Read the Data List according to the display on the GTS.


g.

Touch the unlock sensor on the backside of the rear door outside handle assembly LH.

HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Dr-Door Touch Sensor Rear door LH touch sensor (unlock sensor) ON or OFF ON: Rear door LH touch sensor (unlock sensor) touched
OFF: Rear door LH touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Dr-Door Touch Sensor
50003 125 10
OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (DR-DOOR TRIGGER SWITCH)

NG

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
5.READ VALUE USING GTS (DR-DOOR TRIGGER SWITCH)
a.
B581633C01
0.417,0.333 0.75,0.333 0.75,0.333 1.083,1.167 false 0.25,0.26 0.563,0.458 0.313,0.198 10 false *a
*a Lock Sensor

The illustrations shown are examples only.


Turn the GTS on.


b.

Enter the following menus: Body Electrical / Entry&Start / Data List.


c.

Read the Data List according to the display on the GTS.


d.

Turn the ignition switch off.


e.

Open and close the rear door LH.


f.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


g.

Read the Data List according to the display on the GTS.


h.

Touch the lock sensor of the rear door outside handle assembly LH.

HINT:
·

If the door does not lock even when touching the lock sensor, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Dr-Door Trigger Switch Rear door LH touch sensor (lock sensor) ON or OFF ON: Rear door LH touch sensor (lock sensor) touched
OFF: Rear door LH touch sensor (lock sensor) not touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Dr-Door Trigger Switch
50003 125 14
HINT:

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively. (w/o Double Locking System)


OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

6.CHECK KEY DIAGNOSTIC MODE

NG

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
6.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 1508

b.

Select either channel 1 or channel 2 and perform key diagnostic mode inspection for each channel.

i.
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Subassembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for rear door LH):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the rear door outside handle assembly LH, check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.





Result:
Result Proceed to
Buzzer does not sound A
Buzzer sounds B



A

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F14 rear door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,F14)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(F14)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

G37-1 (CLG3) - F14-6 (ANT1) Always Below 1 Ω
G37-2 (CG3B) - F14-4 (ANT2) Always Below 1 Ω
G37-1 (CLG3) or F14-6 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
G37-2 (CG3B) or F14-4 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the G37 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)
a.
B499513C01
0.135,0.229 0.448,0.385 0.313,0.156 10 false *a 0.167,1.01 0.479,1.167 0.313,0.156 10 false GND
*a Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(F14)Location & Routing

Click Connector(F14)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

F14-6 (ANT1) - F14-4 (ANT2) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

9.CHECK ENTRY LOCK OPERATION

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the entry lock and unlock functions operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

10.REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

10.REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
a.

Replace the rear door outside handle assembly LH with a new one or the rear door outside handle assembly RH if it is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

11.CHECK ENTRY LOCK OPERATION
11.CHECK ENTRY LOCK OPERATION

Result:
Result Proceed to
Entry function operates normally A
Entry function does not operate normally B



A

END (REAR DOOR OUTSIDE HANDLE ASSEMBLY LH WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)