If the entry lock and unlock functions do not operate for the rear door RH only, the request code may not be being transmitted from the rear door RH or the rear door outside handle assembly RH (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and rear door outside handle assembly RH (electrical key antenna)), or there may be wave interference.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
If the rear door RH entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.
| Tester Display |
|---|
| Operation History |
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
| *1 | Electrical Key Transmitter Subassembly |
| *a | Approximately 0.3 m (0.984 ft.) |
The illustrations shown are examples only.
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the rear door outside handle assembly RH and perform an entry function check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear door outside handle assembly RH
When the electrical key transmitter sub-assembly is brought near the rear door outside handle assembly RH, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively. (w/o Double Locking System)
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
| *a | Unlock Sensor (Backside) |
The illustrations shown are examples only.
Turn the ignition switch off.
Open and close the rear door RH.
With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door RH.
Check that the LED of the electrical key transmitter sub-assembly blinks.
Read the Data List according to the display on the GTS.
Touch the unlock sensor on the backside of the rear door outside handle assembly RH.
When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Pr-Door Touch Sensor | Rear door RH touch sensor (unlock sensor) | ON or OFF | ON: Rear door RH touch sensor (unlock sensor) touched
OFF: Rear door RH touch sensor (unlock sensor) not touched |
·
Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate. |
| Tester Display |
|---|
| Pr-Door Touch Sensor |
The GTS display changes correctly in response to the operation of the front door outside handle assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Lock Sensor |
The illustrations shown are examples only.
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
Turn the ignition switch off.
Open and close the rear door RH.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door RH.
Read the Data List according to the display on the GTS.
Touch the lock sensor of the rear door outside handle assembly RH.
If the door does not lock even when touching the lock sensor, touch it with your palm.
When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Pr-Door Trigger Switch | Rear door RH touch sensor (lock sensor) | ON or OFF | ON: Rear door RH touch sensor (lock sensor) touched
OFF: Rear door RH touch sensor (lock sensor) not touched |
·
Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate. |
| Tester Display |
|---|
| Pr-Door Touch Sensor |
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively. (w/o Double Locking System)
The GTS display changes correctly in response to the operation of the rear door outside handle assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antenna in key diagnostic mode.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Select either channel 1 or channel 2 and perform key diagnostic mode inspection for each channel.
| *1 | Electrical Key Transmitter Subassembly |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
The illustrations shown are examples only.
Check the electrical key antenna (for rear door RH):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the rear door outside handle assembly RH, check that the buzzer sounds.
Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| Result | Proceed to |
|---|---|
| Buzzer does not sound | A |
| Buzzer sounds | B |
A
B
Disconnect the G37 certification ECU (smart key ECU assembly) connector.
Disconnect the F3 rear door outside handle assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G37,F3)Location & Routingewd_type=routing;type=c,c;code=G37,F3 Click Connector(G37)Instrument Panel>Floor Wire>Certification ECUewd_type=component;type=c;code=G37;pinno=9,8 Click Connector(F3)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly RHewd_type=component;type=c;code=F3;pinno=6,4 |
||
| G37-9 (CLG4) - F3-6 (ANT1) | Always | Below 1 Ω |
| G37-8 (CG4B) - F3-4 (ANT2) | Always | Below 1 Ω |
| G37-9 (CLG4) or F3-6 (ANT1) - Other terminals and body ground | Always | 10 kΩ or higher |
| G37-8 (CG4B) or F3-4 (ANT2) - Other terminals and body ground | Always | 10 kΩ or higher |
Connect the G37 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Waveform 1 |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
|
Click Location & Routing(F3)Location & Routingewd_type=routing;type=c;code=F3 Click Connector(F3)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly RHewd_type=component;type=c;code=F3;pinno=6,4 |
|||
| F3-6 (ANT1) - F3-4 (ANT2) | Procedure:
1.
Ignition switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
5 V/DIV., 100 ms/DIV. | Pulse generation
(See waveform 1) |
*: For details about the entry function detection area, refer to Operation Check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect all connectors and check that the entry lock and unlock functions operate.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
Replace the rear door outside handle assembly RH with a new one or the rear door outside handle assembly LH if it is functioning properly.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check that the entry lock and unlock functions operate.
| Result | Proceed to |
|---|---|
| Entry function operates normally | A |
| Entry function does not operate normally | B |
A
B