Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2021.08
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the rear door LH only, but the entry unlock function operates, the request code is being transmitted properly from the rear door LH. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (smart key ECU assembly) and rear door outside handle assembly LH).

WIRING DIAGRAM

B622646E01
1.302,0.75 1.917,0.948 0.615,0.198 10 false ANT1 1.302,1.896 1.917,2.094 0.615,0.198 10 false ANT2 1.771,1.917 1.927,2.115 0.156,0.198 10 false 4 1.76,0.75 1.917,0.948 0.156,0.198 10 false 6 4.927,0.865 5.24,1.063 0.313,0.198 10 false G37 4.99,0.635 5.302,0.833 0.313,0.198 10 false 1 5.01,1.813 5.323,2.01 0.313,0.198 10 false 2 5.302,0.75 5.917,0.948 0.615,0.198 10 false CLG3 5.302,1.896 5.917,2.094 0.615,0.198 10 false CG3B 5.833,1.385 6.146,1.583 0.313,0.198 10 false IC 0.479,2.521 1.469,2.75 0.99,0.229 10 false F14 0.49,2.677 2.792,3.385 2.302,0.708 10 false Rear Door Outside Handle Assembly (for Driver Side) 5.104,2.531 6.635,3.49 1.531,0.958 10 false Certification ECU (Smart Key ECU Assembly) 6.479,2.01 6.938,2.208 0.458,0.198 10 false D86 6.531,1.802 6.844,2 0.313,0.198 10 false 18 6.25,2 6.406,2.198 0.156,0.198 10 false E 4.927,2.01 5.24,2.208 0.313,0.198 10 false G37

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (DR-DOOR TRIGGER SWITCH)

NG

2.READ VALUE USING GTS (DR-DOOR TRIGGER SWITCH)
a.
B581633C01
0.417,0.333 0.75,0.333 0.75,0.333 1.083,1.167 false 0.25,0.26 0.563,0.458 0.313,0.198 10 false *a
*a Lock Sensor

The illustrations shown are examples only.


Turn the GTS on.


b.

Enter the following menus: Body Electrical / Entry&Start / Data List.


c.

Read the Data List according to the display on the GTS.


d.

Turn the ignition switch off.


e.

Open and close the rear door LH.


f.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


g.

Read the Data List according to the display on the GTS.


h.

Touch the lock sensor of the rear door outside handle assembly LH.

HINT:
·

If the door does not lock even when touching the lock sensor, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Dr-Door Trigger Switch Rear door LH touch sensor (lock sensor) ON or OFF ON: Rear door LH touch sensor (lock sensor) touched
OFF: Rear door LH touch sensor (lock sensor) not touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Dr-Door Trigger Switch
50003 125 14
HINT:

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively. (w/o Double Locking System)


OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F14 rear door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,F14)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(F14)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

G37-1 (CLG3) - F14-6 (ANT1) Always Below 1 Ω
G37-2 (CG3B) - F14-4 (ANT2) Always Below 1 Ω
G37-1 (CLG3) or F14-6 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
G37-2 (CG3B) or F14-4 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the F14 rear door outside handle assembly LH connector.


e.

Reconnect the G37 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

4.CHECK REAR DOOR OUTSIDE HANDLE ASSEMBLY LH (INPUT TO REAR DOOR LH LOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR DOOR OUTSIDE HANDLE ASSEMBLY LH (INPUT TO REAR DOOR LH LOCK SENSOR)
B443082C50
3.177,0.25 3.594,0.5 0.417,0.25 4.479,0.25 4.896,0.5 0.417,0.25 3.938,2.063 3.854,1.01 true 5.5,2 5.167,1.219 true 0.115,0.094 0.802,0.469 0.688,0.375 10 false *a 3.271,0.292 3.635,0.479 0.365,0.188 10 false G37 4.573,0.281 4.938,0.49 0.365,0.208 10 false D86 5.479,2.042 6.167,2.417 0.688,0.375 10 false E 3.781,2.104 4.469,2.479 0.688,0.375 10 false CLG3 0.99,2.844 1.677,3.219 0.688,0.375 10 false *b 0.771,3.698 1.458,4.073 0.688,0.375 10 false GND 1.167,4.385 1.563,4.625 0.396,0.24 10 false *c 1.969,4.479 2.365,4.719 0.396,0.24 10 false *d 2.792,4.396 3.188,4.635 0.396,0.24 10 false *c
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Lock sensor not touched *d Lock sensor touched


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G37,D86)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

G37-1 (CLG3) - D86-18 (E) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Rear door LH lock sensor touched


5 V/DIV., 40 ms/DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH