Home › Vehicle Interior › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY › from 2021.08
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0448139 FRONT SEAT INNER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT INNER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B608372N01
4,0.667 6.333,2.417 2.333,1.75 4,2.906 6.333,4.656 2.333,1.75 5.177,1.031 5.635,1.031 false 2.094,1.021 2.552,1.021 false 5.365,3.51 5.823,3.51 false 6.365,0.198 6.823,0.198 false 1.885,0.833 2.167,1.188 0.281,0.354 18 false 2 5.708,0.875 5.99,1.229 0.281,0.354 18 false 3 5.865,3.365 6.146,3.719 0.281,0.354 18 false 4 4.073,2.99 4.448,3.229 0.375,0.24 12 false *B 4.073,0.74 4.448,0.979 0.375,0.24 12 false *A 6.146,0.021 6.344,0.323 0.198,0.302 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - - - -
2 FRONT SEAT ASSEMBLY LH - - - -
3 FRONT SEAT INNER BELT ASSEMBLY LH 73240 - - -
4 FRONT SEAT INNER BELT ASSEMBLY RH 73230 - - -

*A for Driver Side *B for Front Passenger Side

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat inner belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
w/ Occupant Classification System
·

Occupant detection ECU (Including removal and installation)

·

Front seat assembly RH (Only for removal and installation)


Zero point calibration (Occupant calssification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

CAUTION:
B543257

·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

(Click here)



Hide 2.REMOVE FRONT SEAT ASSEMBLY LH

Hide 73240 3.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

a.

w/o Seat Position Airbag Sensor:

B622521C01
0,0 0,0 false
V100135

Connector
V100136

Nut



b.

w/ Seat Position Airbag Sensor:

B604442C02
0,0 0,0 false
V100135

Connector
V100136

Nut



Hide 73230 4.REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

a.
B604444C02
0,0 0,0 false
V100135

Connector
V100136

Nut