Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY › from 2021.08
RM37H0E _58 Vehicle Interior _095292 SEAT _0454727 FRONT SEAT ASSEMBLY A

SEAT  FRONT SEAT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B602054N04
4.104,0.594 4.594,0.594 false 6.354,0.188 6.844,0.188 false 4.302,2 4.958,2 false 4.979,3.24 5.604,3.24 false 5.26,2.823 5.885,2.823 false 0.708,4.313 1.333,4.313 false 0.906,3.896 1.531,3.896 false 5.24,4.427 5.885,4.427 false 4.521,3.719 5.146,3.719 false 6.188,0.052 6.667,0.344 0.479,0.292 18 false 1 4.646,0.458 5.125,0.75 0.479,0.292 18 false 2 0.542,4.156 1.021,4.448 0.479,0.292 18 false 3 1.573,3.74 2.052,4.031 0.479,0.292 18 false 4 4.823,3.083 5.302,3.375 0.479,0.292 18 false 5 6.292,4.271 6.615,4.542 0.323,0.271 18 false 7 5.281,1.875 5.604,2.146 0.323,0.271 18 false 8 5.948,2.635 6.177,2.927 0.229,0.292 18 false 6 5.188,3.625 5.51,3.896 0.323,0.271 10 false *1 1.823,2.958 2.281,3.156 0.458,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 FRONT SEAT HEADREST ASSEMBLY 71910A - - -
3 FRONT OUTER SEAT TRACK BRACKET COVER LH 72124 - - -
4 FRONT INNER SEAT TRACK BRACKET COVER LH 72128A - - -
5 REAR OUTER SEAT TRACK BRACKET COVER LH 72138N - - -
6 REAR INNER SEAT TRACK BRACKET COVER LH 72158E - - -
7 SEAT BELT ANCHOR COVER CAP LH 73179A (Click here) - -
8 FRONT SEAT ASSEMBLY LH - (Click here) - -

*1 FRONT SEAT OUTER BELT ASSEMBLY LH - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Front power seat control system (w/ Memory)
·

Position control ECU assembly LH (for LHD)*

·

Position control ECU assembly RH (for RHD)*

·

Front power seat switch LH (for LHD)*

·

Front power seat switch RH (for RHD)*

·

Front seat back frame sub-assembly LH (for LHD)*

·

Front seat back frame sub-assembly RH (for RHD)*

·

Front power seat adjuster assembly LH (for LHD)*

·

Front power seat adjuster assembly RH (for RHD)*

·

Front power seat tilt motor assembly LH (for LHD)*

·

Front power seat tilt motor assembly RH (for RHD)*

·

Front power seat lifter motor assembly LH (for LHD)*

·

Front power seat lifter motor assembly RH (for RHD)*


Initialize position control ECU Front power seat control system (w/ Memory) (Click here)
w/ Occupant Classification System
·

Occupant detection ECU (Including removal and installation)

·

Front seat assembly RH (Only for removal and installation)


Zero point calibration (Occupant calssification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

CAUTION:
B543257

·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



NOTICE:
·

If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback spring assembly LH, front seatback pad LH and front seatback cover LH with the necessary parts in accordance with the extent of the collision damage.

·

Replace any other damaged parts as necessary.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

(Click here)



Hide 71910A 2.REMOVE FRONT SEAT HEADREST ASSEMBLY

a.
B604464


Hide 72124 3.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH

a.
B603145C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction



Hide 72128A 4.REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH

a.

Use the same procedure described for the outer side.


Hide 72138N 5.REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH

a.
B603146C02
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 72158E 6.REMOVE REAR INNER SEAT TRACK BRACKET COVER LH

a.

Use the same procedure described for the outer side.


Hide 73179A 7.REMOVE SEAT BELT ANCHOR COVER CAP LH

a.
B603147C02
0.396,0.104 0.677,0.458 0.281,0.354 18 true i 4.656,1.792 4.844,2.063 0.188,0.271 18 true ii 4.448,1.438 4.656,1.708 0.208,0.271 18 true ii 5.208,0.781 5.417,1.052 0.208,0.271 18 true iii 4.375,0.719 4.583,0.99 0.208,0.271 18 true iii 5.656,0.646 5.865,0.917 0.208,0.271 18 true iii
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2) - -


i.

Using moulding remover A, detach the clip.


ii.

Place your hand at the position shown in the illustration and pull in the removal direction (1) to detach the clip.


iii.

Slide in the removal direction (2) shown in the illustration, detach the guide and remove the seatbelt anchor cover cap LH.



Hide 8.REMOVE FRONT SEAT ASSEMBLY LH

a.
B603148C05
0.771,0.115 1.052,0.469 0.281,0.354 18 true i 5.76,0.635 5.948,0.906 0.188,0.271 18 true ii 5.51,1.313 5.729,1.594 0.219,0.281 18 true iii 0.25,0.156 0.625,0.396 0.375,0.24 12 false *A
*A for Driver Seat - -


i.

for Driver Seat:

1. Operate the slide and vertical power seat switch knob to slide the front seat assembly LH to the lowermost position.


ii.

Remove the bolt.


iii.

Detach the guide and disconnect the anchor of the front outer belt assembly LH.



b.
B603149N01
0.354,1.177 0.542,1.417 0.188,0.24 18 true i 1.417,1.25 1.604,1.49 0.188,0.24 18 true i 1.688,0.854 1.875,1.094 0.188,0.24 18 true ii 2,0.115 2.208,0.354 0.208,0.24 18 true iii 2.219,1.438 2.438,1.677 0.219,0.24 18 true iii 4.51,0.635 4.698,0.875 0.188,0.24 18 true v 3.833,1.104 4.063,1.344 0.229,0.24 18 true vi 3.271,1.135 3.5,1.375 0.229,0.24 18 true iv 5.479,0.417 5.74,0.667 0.26,0.25 18 true vii

i.

Using a T50 "TORX" socket wrench, remove the 2 TORX screws.


ii.

Operate the slide and vertical power seat switch knob to slide the front seat assembly LH to the rearmost position.


iii.

Using a T50 "TORX" socket wrench, remove the 2 TORX screws.


iv.

Operate the power seat switch knob to slide the front seat assembly LH to the center position.


v.

Operate the reclining power seat switch knob to set the seatback of the front seat assembly LH to the perpendicular position.


vi.

for Driver Seat:

1. Operate the slide and vertical power seat switch knob to set the seat cushion height and vertical position of the front seat assembly LH to the uppermost position.


vii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal.

·

If the airbag deploys for any reason, it may cause a serious accident.





c.
B603150C02
0.167,0.094 0.542,0.333 0.375,0.24 12 false *A 3.771,0.094 4.146,0.333 0.375,0.24 12 false *B 6.063,0.958 6.24,1.24 0.177,0.281 18 true i 1.448,0.938 1.656,1.219 0.208,0.281 18 true i 4.49,0.51 4.698,0.792 0.208,0.281 18 true ii 6,0.344 6.208,0.625 0.208,0.281 18 true ii 2.323,0.229 2.531,0.51 0.208,0.281 18 true ii 1.083,0.115 1.292,0.396 0.208,0.281 18 true ii 2.24,1.344 2.448,1.625 0.208,0.281 18 true ii 2.281,0.865 2.49,1.146 0.208,0.281 18 true ii 4.938,0.917 5.146,1.198 0.208,0.281 18 true ii 4.979,1.354 5.188,1.635 0.208,0.281 18 true ii
*A for Driver Seat *B for Front Passenger Seat


i.

Disconnect the connector of the front seat airbag assembly LH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR

NOTICE:

Do not pull while holding the wire harness.



ii.

Disconnect the 2 connectors and wire harness protector.



d.
B603151N02
0.406,0.031 0.688,0.385 0.281,0.354 18 false i

i.

Remove and carry the front seat assembly LH out of the vehicle.

NOTICE:
·

Protect the front seat legs.

·

Carrying the front seat assembly LH from the vehicle must be performed by multiple people.

·

Do not damage the front seat assembly LH, body exterior or interior parts.