Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1EF214  Air Valve Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

For the FC control ECU motor and solenoid drive power source, power is supplied to each motor and solenoid after voltage is supplied from the +BP3 terminal.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1EF214 Air Valve Supply Voltage Circuit Short to Ground or Open If the +B voltage is not low when the ignition switch is ON, +BP3 voltage remains at less than 4.5 V for more than 3 seconds.
(1 trip detection logic)
·

FC control ECU

·

Wire harness or connector


Master Warning: Comes on FC A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is travelling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List
DTC No. Data List
P1EF214 Air Valve Supply Voltage

WIRING DIAGRAM

A492225E03
1.958,3.635 3.333,3.948 1.375,0.313 10 false EV Control ECU 0.74,4.583 1.865,4.781 1.125,0.198 10 false Auxiliary Battery 5.469,4.813 6.698,5.156 1.229,0.344 10 false FC Control ECU 1.969,3.458 2.448,3.625 0.479,0.167 10 false A8*1 2.604,2.958 3.083,3.125 0.479,0.167 10 false MREL 3.115,2.823 3.594,2.99 0.479,0.167 10 false 21 1.458,1.469 2.219,1.635 0.76,0.167 10 false FC-B NO. 1 2.552,2.073 3.313,2.24 0.76,0.167 10 false FC-B 0.594,1.469 1.438,1.646 0.844,0.177 10 false R/B-B NO. 1 0.563,2.323 1.406,2.5 0.844,0.177 10 false R/B FR 2.292,1.198 2.771,1.396 0.479,0.198 10 false 3 3.094,1.188 3.573,1.385 0.479,0.198 10 false 5 2.26,1.635 2.74,1.833 0.479,0.198 10 false 2 3.115,1.615 3.594,1.813 0.479,0.198 10 false 1 3.844,1.063 4.604,1.229 0.76,0.167 10 false FC-B NO. 2 3.833,1.49 4.594,1.656 0.76,0.167 10 false FC-B NO. 4 5.031,4.333 5.396,4.542 0.365,0.208 10 false A48 5.063,3.5 5.427,3.708 0.365,0.208 10 false B1 5.031,1.323 5.396,1.531 0.365,0.208 10 false A48 5.073,0.906 5.438,1.115 0.365,0.208 10 false B1 5.063,0.531 5.427,0.74 0.365,0.208 10 false B1 5.063,0.344 5.427,0.552 0.365,0.208 10 false 43 5.073,0.729 5.438,0.938 0.365,0.208 10 false 83 5.094,1.135 5.458,1.344 0.365,0.208 10 false 2 5.021,3.313 5.385,3.521 0.365,0.208 10 false 104 5.073,4.156 5.438,4.365 0.365,0.208 10 false 21 5.365,4.344 5.729,4.552 0.365,0.208 10 false E03 5.365,3.5 5.729,3.708 0.365,0.208 10 false E1 5.375,0.531 5.74,0.74 0.365,0.208 10 false +B1 5.375,0.906 5.74,1.115 0.365,0.208 10 false +B2 5.354,1.333 5.802,1.542 0.448,0.208 10 false +BP3 5.021,3.74 5.385,3.948 0.365,0.208 10 false 105 5.073,3.917 5.438,4.125 0.365,0.208 10 false B1 5.354,3.927 5.719,4.135 0.365,0.208 10 false E2 1.188,5.083 2.042,5.333 0.854,0.25 10 false *1: for LHD 2.354,3.458 2.833,3.625 0.479,0.167 10 false D15*2 1.188,5.385 2.042,5.635 0.854,0.25 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-104 (E1) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC control ECU connector.



OK

2.READ VALUE USING GTS (AIR VALVE SUPPLY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING GTS (AIR VALVE SUPPLY VOLTAGE)
a.

Read the value of Air Valve Supply Voltage.

Powertrain > FC > Data List
Tester Display
Air Valve Supply Voltage
50003 490 9
Result:
Result Proceed to
The value of Air Valve Supply Voltage is between 11 and 14 V A
None of the above conditions are met B




A

B

3.INSPECT FC CONTROL ECU (+BP3 VOLTAGE)
3.INSPECT FC CONTROL ECU (+BP3 VOLTAGE)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

A48-2 (+BP3) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC control ECU connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC-B RELAY)
4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC-B RELAY)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Remove the FC-B relay from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

A48-2 (+BP3) - 5 (FC-B relay holder) Always Below 1 Ω
A48-2 (+BP3) or 5 (FC-B relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reinstall the FC-B relay.


b.

Reconnect the FC control ECU connector.



OK

GO TO ECU POWER SOURCE CIRCUIT (FC CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR