Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D5F87  Lost Communication with Cell Monitor Missing Message  


DESCRIPTION

The FC Boost Control ECU receives communication signals for the FC stack cell voltage via the cell monitor (built into the FC stack assembly). The FC Boost Control ECU detects errors in the communication with the cell monitor.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D5F87 Lost Communication with Cell Monitor Missing Message All of the following conditions are met, and a cell monitor communication error continues for 1 second or more.
·

Auxiliary battery voltage is 10 V or higher for 3 seconds or more

·

+B voltage is not low


(1 trip detection logic)
·

FC boost control ECU

·

Cell monitor (FC stack voltage sensor)

·

No. 3 FC converter wire

·

FC stack monitor wire


Master Warning: Comes on FCDC A

Related Data List
DTC No. Data List
P1D5F87 -

WIRING DIAGRAM

A478990E03
0.563,0.25 0.719,0.448 0.156,0.198 10 false 3 0.667,1.01 1.49,1.219 0.823,0.208 10 false IGCT NO. 1 0.385,2.313 1.552,2.552 1.167,0.24 10 false R/R RR# 2 0.573,3.063 1.75,3.344 1.177,0.281 10 false Auxiliary Battery 3.938,4.125 4.302,4.469 0.365,0.344 10 false B6 1.542,1.208 1.76,1.406 0.219,0.198 10 false 21 1.792,1.344 2.552,1.573 0.76,0.229 10 false MREL 1.75,2.115 2.979,2.385 1.229,0.271 10 false EV Control ECU 3.938,4.271 5.51,4.635 1.573,0.365 10 false FC Converter Assembly 5.594,4.177 6.885,4.396 1.292,0.219 10 false FC Stack Assembly 3.698,2.646 4.458,2.875 0.76,0.229 10 false E1 3.406,2.927 3.635,3.125 0.229,0.198 10 false 11 4.042,0.385 4.802,0.615 0.76,0.229 10 false CMPWC 4.198,1.281 4.958,1.51 0.76,0.229 10 false DCCH 3.698,3.031 4.458,3.26 0.76,0.229 10 false E2 4.146,3.042 4.906,3.271 0.76,0.229 10 false CMGO 3.406,2.552 3.583,2.76 0.177,0.208 10 false 10 3.406,0.667 4.167,0.896 0.76,0.229 10 false 13 3.406,0.25 3.625,0.542 0.219,0.292 10 false 12 0.573,0.635 0.729,0.833 0.156,0.198 10 false 1 1.313,0.625 1.469,0.823 0.156,0.198 10 false 2 1.323,0.24 1.479,0.438 0.156,0.198 10 false 5 6.219,3.333 7.031,3.688 0.813,0.354 10 false Cell Monitor 4.208,2.156 4.969,2.385 0.76,0.229 10 false DCCL 3.698,0.802 4.458,1.031 0.76,0.229 10 false +B2 3.708,0.385 4.469,0.615 0.76,0.229 10 false +B1 0.375,1.677 1.198,1.885 0.823,0.208 10 false IGCT NO. 1 1.688,3.938 2.635,4.177 0.948,0.24 10 false *1: for LHD 3.698,3.344 5.24,3.708 1.542,0.365 10 false FC Boost Control ECU 6.26,0.385 7.021,0.615 0.76,0.229 10 false CMPWC 6.24,1.271 7,1.5 0.76,0.229 10 false DCCH 6.25,2.156 7.01,2.385 0.76,0.229 10 false DCCL 6.25,3.052 7.01,3.281 0.76,0.229 10 false CMGO 1.854,0.531 2.677,0.74 0.823,0.208 10 false IGCT NO. 7 2.104,1.958 2.625,2.323 0.521,0.365 10 false D15*2 1.698,4.229 2.646,4.469 0.948,0.24 10 false *2: for RHD 1.75,1.948 2.271,2.313 0.521,0.365 10 false A8*1

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (w/ 1500W Type Voltage Inverter)


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 2 minutes or more.



PROCEDURE

1.REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


·

FC boost control ECU

·

Cell monitor (FC stack voltage sensor)

·

No. 3 FC converter wire

·

FC stack monitor wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION



Result:
Proceed to
NEXT



NEXT

END