Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0490698 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1780  Front Occupant Classification Sensor LH Circuit Malfunction  


DESCRIPTION

The front occupant classification sensor LH circuit consists of the occupant detection ECU and front occupant classification sensor LH.

DTC B1780 is stored when a malfunction is detected in the front occupant classification sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1780 Front Occupant Classification Sensor LH Circuit Malfunction
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the front occupant classification sensor LH circuit.

·

Front occupant classification sensor LH malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Front seat adjuster assembly RH (Front occupant classification sensor LH)*

·

Occupant detection ECU


Occupant Detection A

*: The front occupant classification sensor LH is built into the front seat adjuster assembly RH.


WIRING DIAGRAM

C376642E20
5.156,2.896 5.531,3.063 0.375,0.167 10 false L19 5.156,3.073 6.823,3.438 1.667,0.365 10 false Occupant Detection ECU 0.052,2.875 0.521,3.073 0.469,0.198 10 false L23 0.063,3.052 2.531,3.396 2.469,0.344 10 false Front Seat Adjuster Assembly RH (Front Occupant Classification sensor LH) 1.875,0.5 2.219,0.698 0.344,0.198 10 false 1 5.115,0.49 5.26,0.708 0.146,0.219 10 false 1 1.896,1.365 2.125,1.552 0.229,0.188 10 false 2 5.115,1.354 5.281,1.573 0.167,0.219 10 false 3 1.896,2.229 2.125,2.448 0.229,0.219 10 false 3 5.135,2.24 5.281,2.417 0.146,0.177 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

When RoB X1202 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1780 is output, perform troubleshooting for this DTC first.

·

If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

a.

Check that the connectors are properly connected to the occupant detection ECU and front occupant classification sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

2.CHECK CONNECTORS

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

a.

Check that the connectors are properly connected to the occupant detection ECU and front occupant classification sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



b.

Disconnect the connectors from the occupant detection ECU and front occupant classification sensor LH.


c.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

3.CHECK FRONT SEAT WIRE RH

Pre-procedure1

a.
E459527C01
0.854,0.583 1.271,0.823 0.417,0.24 0.51,3.5 0.938,3.74 0.427,0.24 0.677,2.458 1.094,2.781 0.417,0.323 10 false *1 2.406,2.677 2.885,3.177 0.479,0.5 10 false *2 1.521,2.229 1.938,2.479 0.417,0.25 10 false *3 0.75,0.24 1.063,0.573 0.313,0.333 10 false *a 0.313,2.948 0.708,3.271 0.396,0.323 10 false *b 0.594,3.542 1.01,3.781 0.417,0.24 10 false L23 0.927,0.615 1.406,0.948 0.479,0.333 10 false L19 2.104,2.021 2.583,2.521 0.479,0.5 10 false A 1.823,2.021 2.302,2.521 0.479,0.5 10 false B 1.208,2.021 1.688,2.521 0.479,0.5 10 false C 0.927,2.021 1.406,2.521 0.479,0.5 10 false D
*1 Front Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Occupant Classification Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L19)Location & Routing

Click Connector(L19)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Occupant Detection ECU

L19-1 - Body ground Ignition switch ON Below 1 V
L19-3 - Body ground Ignition switch ON Below 1 V
L19-5 - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

4.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH

Pre-procedure1

a.
C295786C35
0.854,0.583 1.271,0.823 0.417,0.24 0.51,3.5 0.938,3.74 0.427,0.24 2.083,3.063 2.417,3.063 true 2.01,4.063 2.344,4.063 true 0.677,2.458 1.094,2.781 0.417,0.323 10 false *1 2.49,2.979 2.792,3.177 0.302,0.198 10 false *4 1.521,2.229 1.938,2.479 0.417,0.25 10 false *3 0.75,0.24 1.063,0.573 0.313,0.333 10 false *a 0.313,2.948 0.708,3.271 0.396,0.323 10 false *b 0.594,3.542 1.01,3.781 0.417,0.24 10 false L23 0.927,0.615 1.406,0.948 0.479,0.333 10 false L19 2.104,2.021 2.583,2.521 0.479,0.5 10 false A 1.823,2.021 2.302,2.521 0.479,0.5 10 false B 1.208,2.021 1.688,2.521 0.479,0.5 10 false C 0.927,2.021 1.406,2.521 0.479,0.5 10 false D 2.375,2.656 2.854,3.156 0.479,0.5 10 false *2 2.396,4 2.698,4.198 0.302,0.198 10 false *4
*1 Front Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Occupant Classification Sensor LH)


Using service wires, connect terminals 1 and 3, and terminals 2 and 3 of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L19)Location & Routing

Click Connector(L19)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Occupant Detection ECU

L19-1 - L19-5 Always Below 1 Ω
L19-3 - L19-5 Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wires from connector C.



OK

5.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FRONT SEAT WIRE RH
a.
E459527C01
0.854,0.583 1.271,0.823 0.417,0.24 0.51,3.5 0.938,3.74 0.427,0.24 0.677,2.458 1.094,2.781 0.417,0.323 10 false *1 2.406,2.677 2.885,3.177 0.479,0.5 10 false *2 1.521,2.229 1.938,2.479 0.417,0.25 10 false *3 0.75,0.24 1.063,0.573 0.313,0.333 10 false *a 0.313,2.948 0.708,3.271 0.396,0.323 10 false *b 0.594,3.542 1.01,3.781 0.417,0.24 10 false L23 0.927,0.615 1.406,0.948 0.479,0.333 10 false L19 2.104,2.021 2.583,2.521 0.479,0.5 10 false A 1.823,2.021 2.302,2.521 0.479,0.5 10 false B 1.208,2.021 1.688,2.521 0.479,0.5 10 false C 0.927,2.021 1.406,2.521 0.479,0.5 10 false D
*1 Front Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Occupant Classification Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L19)Location & Routing

Click Connector(L19)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Occupant Detection ECU

L19-1 - L19-5 Always 1 MΩ or higher
L19-3 - L19-5 Always 1 MΩ or higher
L19-1 - L19-3 Always 1 MΩ or higher
L19-1 - Body ground Always 1 MΩ or higher
L19-3 - Body ground Always 1 MΩ or higher
L19-5 - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPLACE FRONT SEAT WIRE RH

6.CLEAR DTC
a.

Connect the connectors to the occupant detection ECU and front occupant classification sensor LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC
7.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 10 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394

Result:
Result Proceed to
B1780 is not output A
B1780 is output B


HINT:

Codes other than DTC B1780 may be output at this time, but they are not related to this check.


Post-procedure1

a.

None



A

B

8.CHECK OCCUPANT DETECTION ECU
8.CHECK OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the occupant detection ECU with a new one.

HINT:
·

Perform the following inspection using known good parts from another vehicle if possible.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

Result:
Proceed to
NEXT



NEXT

9.CHECK OCCUPANT DETECTION ECU
9.CHECK OCCUPANT DETECTION ECU

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 10 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394

Result:
Result Proceed to
B1780 is not output A
B1780 is output B


HINT:

Codes other than DTC B1780 may be output at this time, but they are not related to this check.


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Restore the occupant detection ECU that was installed for testing to its original location.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>INSTALLATION




A

10.REPLACE OCCUPANT DETECTION ECU

B

12.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
10.REPLACE OCCUPANT DETECTION ECU
a.

Replace the occupant detection ECU with a new one.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL



b.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION


Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

12.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Replace the front seat adjuster assembly RH with a new one.

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



b.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

13.PERFORM ZERO POINT CALIBRATION
13.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION


Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (FRONT SEAT ADJUSTER ASSEMBLY RH WAS DEFECTIVE)