| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B00B512 | Driver Seat Track Position Restraints Sensor Circuit Short to Battery | One of the following conditions is met:
·
The airbag ECU assembly detects a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds. ·
A front seat adjuster assembly LH (seat position airbag sensor) malfunction. ·
An airbag ECU assembly malfunction. |
·
Wire harness ·
Front seat adjuster assembly LH (seat position airbag sensor) ·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
To perform the simulation method, shake each connector of the airbag system or drive the vehicle on various types of road.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly LH (seat position airbag sensor).
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Front Seat Inner Belt Assembly LH |
| *4 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the front seat adjuster assembly LH (seat position airbag sensor) connector.
Procedure1
Check that the connectors (on the airbag ECU assembly side and front seat adjuster assembly LH (seat position airbag sensor) side) are not damaged.
The terminals of the connectors are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Front Seat Inner Belt Assembly LH |
| *4 | Wire Harness |
| *a | Front view of wire harness connector
(to Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L45)Location & Routingewd_type=routing;type=c;code=L45 Click Connector(L45)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Position Airbag Sensorewd_type=component;type=c;code=L45;pinno=2,1 |
||
| L45-2 - Body ground | Ignition switch ON | Below 1 V |
| L45-1 - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Front Seat Inner Belt Assembly LH |
| *4 | Wire Harness |
Reconnect the airbag ECU assembly connector.
Reconnect the front seat adjuster assembly LH (seat position airbag sensor) connector.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B00B512 is output | A |
| B00B513 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
| *1 | Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Front Seat Inner Belt Assembly LH |
| *4 | Wire Harness |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Disconnect the airbag ECU assembly connector.
Disconnect the front seat adjuster assembly LH (seat position airbag sensor) connector.
Procedure1
Check that the connectors (on the front seat inner belt assembly LH side and wir harness side) are not damaged.
The terminals of the connectors are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Front Seat Inner Belt Assembly LH |
| *4 | Wire Harness |
| *a | Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G23)Location & Routingewd_type=routing;type=c;code=G23 Click Connector(G23)Seat>Floor Wire>Front Seat Inner Belt Assembly LHewd_type=component;type=c;code=G23;pinno=4,3 |
||
| G23-4 (LSP+) - Body ground | Ignition switch ON | Below 1 V |
| G23-3 (LSP-) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
OK
NG