Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR CLOSER SYSTEM › from 2021.08
RM37H0E _59 Vehicle Exterior _095314 DOOR / HATCH _0491385 LUGGAGE COMPARTMENT DOOR CLOSER SYSTEM C

DOOR / HATCH  LUGGAGE COMPARTMENT DOOR CLOSER SYSTEM  B2250  PBD/PTL Closer Operation  


DESCRIPTION

DTC B2250 is output if the closer pulse sensor of the multiplex network door ECU has a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B2250 PBD/PTL Closer Operation When closer pulse sensor of luggage door closer assembly has malfunction
·

Luggage door closer assembly

·

Multiplex network door ECU

·

Harness or connector


Not applicable Back Door A

WIRING DIAGRAM

E456452E01
1.167,2.167 1.479,2.365 0.313,0.198 10 false IC 1.146,3.115 1.458,3.313 0.313,0.198 10 false IC 6.094,2.083 6.406,2.281 0.313,0.198 10 false IC 2.344,3.323 2.958,3.521 0.615,0.198 10 false CPSE 2.354,2.969 2.969,3.167 0.615,0.198 10 false CPS2 2.354,1.979 2.969,2.177 0.615,0.198 10 false CPS1 2.344,1.656 2.958,1.854 0.615,0.198 10 false CPS+ 4.167,1.667 4.781,1.865 0.615,0.198 10 false CSV 4.167,1.99 4.781,2.188 0.615,0.198 10 false CS1 4.188,2.958 4.802,3.156 0.615,0.198 10 false CS2 4.198,3.333 4.813,3.531 0.615,0.198 10 false CSG 0.76,3.958 1.219,4.156 0.458,0.198 10 false K2 4.156,0.667 4.771,0.865 0.615,0.198 10 false LCM+ 4.167,1.115 4.781,1.313 0.615,0.198 10 false LCM- 2.51,0.646 2.823,0.844 0.313,0.198 10 false M+ 2.531,1.125 2.844,1.323 0.313,0.198 10 false M- 0.771,4.125 2.76,4.323 1.99,0.198 10 false Luggage Door Closer Assembly 4.417,4.146 6.219,4.365 1.802,0.219 10 false Multiplex Network Door ECU 4.417,3.958 4.875,4.156 0.458,0.198 10 false G15 1.24,1.479 2.313,1.677 1.073,0.198 10 false Closer Motor 2.854,0.656 3.01,0.854 0.156,0.198 10 false 8 2.854,1.135 3.01,1.333 0.156,0.198 10 false 1 3.885,2.948 4.198,3.146 0.313,0.198 10 false 17 3.958,1.115 4.115,1.313 0.156,0.198 10 false 7 3.958,0.667 4.115,0.865 0.156,0.198 10 false 6 2.854,1.656 3.01,1.854 0.156,0.198 10 false 3 2.854,1.99 3.01,2.188 0.156,0.198 10 false 2 2.854,2.969 3.01,3.167 0.156,0.198 10 false 9 2.865,3.333 3.021,3.531 0.156,0.198 10 false 4 4.833,0.552 5.146,0.75 0.313,0.198 10 false +B 4.906,1.615 5.219,1.813 0.313,0.198 10 false +B 3.969,1.667 4.125,1.865 0.156,0.198 10 false 4 3.958,2 4.115,2.198 0.156,0.198 10 false 5 3.979,3.313 4.135,3.51 0.156,0.198 10 false 9

CAUTION / NOTICE / HINT

NOTICE:

If a multiplex network door ECU DTC is output, the luggage compartment door closer stops operating.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - LUGGAGE DOOR CLOSER ASSEMBLY)

Pre-procedure1

a.

Disconnect the G15 multiplex network door ECU connector.


b.

Disconnect the K2 luggage door closer assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G15,K2)Location & Routing

Click Connector(G15)Body>Floor Wire / No. 3 Floor Wire>Multiplex Network Door ECU

Click Connector(K2)Body>No. 1 Back Door Wire>Luggage Door Closer Assembly

G15-4 (CSV) - K2-3 (CPS+) Always Below 1 Ω
G15-5 (CS1) - K2-2 (CPS1) Always Below 1 Ω
G15-9 (CSG) - K2-4 (CPSE) Always Below 1 Ω
G15-17 (CS2) - K2-9 (CPS2) Always Below 1 Ω
G15-4 (CSV) or K2-3 (CPS+) - Body ground Always 10 kΩ or higher
G15-5 (CS1) or K2-2 (CPS1) - Body ground Always 10 kΩ or higher
G15-9 (CSG) or K2-4 (CPSE) - Body ground Always 10 kΩ or higher
G15-17 (CS2) or K2-9 (CPS2) - ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK LUGGAGE DOOR CLOSER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK LUGGAGE DOOR CLOSER ASSEMBLY

Pre-procedure1

a.

Disconnect the K2 luggage door closer assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K2)Location & Routing

Click Connector(K2)Body>No. 1 Back Door Wire>Luggage Door Closer Assembly

K2-4 (CPSE) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(K2)Location & Routing

Click Connector(K2)Body>No. 1 Back Door Wire>Luggage Door Closer Assembly

K2-2 (CPS1) - Body ground Ignition switch ON, luggage compartment door closer not operate 7 V or higher
K2-3 (CPS+) - Body ground Ignition switch ON, luggage compartment door closer not operate 7 V or higher
K2-9 (CPS2) - Body ground Ignition switch ON, luggage compartment door closer not operate 7 V or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK LUGGAGE DOOR CLOSER ASSEMBLY

NG

REPLACE MULTIPLEX NETWORK DOOR ECU

3.CHECK LUGGAGE DOOR CLOSER ASSEMBLY

Pre-procedure1

a.

Disconnect the K2 luggage door closer assembly connector.


b.

Disconnect terminals 8 (M+) and 1 (M-) from the luggage door closer assembly connector.


c.

Reconnect the K2 luggage door closer assembly connector.


Procedure1

a.

Using an oscilloscope, check the waveform.

E455712C02
5.479,0.667 5.865,0.917 0.385,0.25 6.365,0.885 6.167,0.885 6.167,0.885 5.906,1.427 true 6.302,2.26 6.135,2.26 6.135,2.26 5.917,1.646 true 4.521,0.646 4.833,0.802 0.313,0.156 10 false *a 0.854,2.938 1.167,3.094 0.313,0.156 10 false *b 3.729,2.885 4.042,3.042 0.313,0.156 10 false *c 3.344,4.365 3.802,4.563 0.458,0.198 10 false GND 6.177,4.365 6.583,4.583 0.406,0.219 10 false GND 5.594,0.719 6.052,0.917 0.458,0.198 10 false K2 6.406,2.177 6.854,2.354 0.448,0.177 10 false CPS2 6.458,0.802 7.073,1 0.615,0.198 10 false CPS1
*a Component with harness connected
(Luggage Door Closer Assembly)
*b Waveform 1
*c Waveform 2 - -


NOTICE:

Do not operate any other functions until this inspection is finished.


OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(K2)Location & Routing

Click Connector(K2)Body>No. 1 Back Door Wire>Luggage Door Closer Assembly

K2-2 (CPS1) - Body ground Apply auxiliary battery voltage to the terminals removed from the connector and operate the luggage door closer assembly (closer motor) 2 V/DIV., 10 ms./DIV. Pulse generation
(waveform 1)
K2-9 (CPS2) - Body ground Apply auxiliary battery voltage to the terminals removed from the connector and operate the luggage door closer assembly (closer motor) 2 V/DIV., 10 ms./DIV. Pulse generation
(waveform 2)



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE LUGGAGE DOOR CLOSER ASSEMBLY