Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0455415 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK COMBINATION METER ASSEMBLY


B345456N25
3.323,0.104 3.823,0.354 0.5,0.25 3.438,0.156 3.917,0.406 0.479,0.25 10 false D41

a.

Disconnect the D41 combination meter assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


w/ Occupant Classification System:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D41-22 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
D41-21 (IG+) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
D41-31 (ES) - Body ground Ground Always Below 1 Ω
D41-14 (RLSB) - Body ground Rear LH seat belt buckle switch and occupant detection signal Rear LH seat occupied, seat belt fastened 10 kΩ or higher
Rear LH seat occupied, seat belt unfastened Below 1 Ω
D41-12 (RRSB) - Body ground Rear RH seat belt buckle switch and occupant detection signal Rear RH seat occupied, seat belt fastened 10 kΩ or higher
Rear RH seat occupied, seat belt unfastened Below 1 Ω
D41-13 (RCSB) - Body ground Rear center seat belt buckle switch and occupant detection signal Rear center seat occupied, seat belt fastened 10 kΩ or higher
Rear center seat occupied, seat belt unfastened Below 1 Ω

w/o Occupant Classification System:
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/o All Auto Control

D41-22 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
D41-21 (IG+) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
D41-31 (ES) - Body ground Ground Always Below 1 Ω
D41-14 (RLSB) - Body ground Rear occupant detection sensor LH signal signal Rear LH seat occupied 10 kΩ or higher
Rear LH seat not occupied Below 1 Ω
D41-12 (RRSB) - Body ground Rear occupant detection sensor RH signal Rear RH seat occupied 10 kΩ or higher
Rear RH seat not occupied Below 1 Ω
D41-13 (RCSB) - Body ground Rear occupant detection sensor center signal signal Rear center seat occupied 10 kΩ or higher
Rear center seat not occupied Below 1 Ω
D41-6 (PODS) - Body ground Occupant detection sensor signal Front passenger seat occupied Below 100 Ω
Front passenger seat not occupied 1 MΩ or higher
D41-18 (PBKL) - Body ground* Front passenger seat belt buckle switch signal Front passenger seat belt fastened 10 kΩ or higher
Front passenger seat belt unfastened Below 1 Ω



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C01
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the driver side junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/o Occupant Classification System

A-32 (IG) - Body ground Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground Ground Always Below 1 Ω
A-18 (DBKL) - Body ground* Driver seat belt buckle switch signal Driver seat belt fastened 10 kΩ or higher
Driver seat belt unfastened Below 1 Ω



EV CONTROL ECU (w/o Occupant Classification System)


A352214C19
0.646,0.052 1.115,0.406 0.469,0.354 1.958,0.271 2.427,0.625 0.469,0.354 3.365,0.271 3.833,0.625 0.469,0.354 4.729,0.271 5.198,0.625 0.469,0.354 6.021,0.469 6.49,0.823 0.469,0.354 0.646,0.479 1.115,0.833 0.469,0.354 6.021,0.052 6.49,0.406 0.469,0.354 0.76,0.135 1.219,0.333 0.458,0.198 10 false G14 2.083,0.375 2.542,0.573 0.458,0.198 10 false A15 3.49,0.385 3.948,0.583 0.458,0.198 10 false A16 4.833,0.385 5.292,0.583 0.458,0.198 10 false A17 6.177,0.146 6.635,0.344 0.458,0.198 10 false A8 0.771,0.583 1.229,0.781 0.458,0.198 10 false A14 1.156,0.063 1.469,0.26 0.313,0.198 10 false *A 1.156,0.51 1.469,0.708 0.313,0.198 10 false *B 6.156,0.573 6.615,0.771 0.458,0.198 10 false D15 6.542,0.073 6.854,0.271 0.313,0.198 10 false *A 6.552,0.5 6.865,0.698 0.313,0.198 10 false *B 0.135,0.24 0.448,0.438 0.313,0.198 10 false *1
*A for RHD *B for LHD
*1 EV Control ECU - -


a.

Measure the voltage and resistance according to the value(s) in the table below.

for RHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ All Auto Control

D15-1 (BATT) - A17-4 (E1) Constant power source Ignition switch ON 11 to 14 V
Ignition switch ON (READY) 11 to 15.5 V
A16-7(IG2) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
A17-1(+B1) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
D15-7 (+B2) - A17-4 (E1) Power source Ignition switch ON 11 to 14 V
A16-8 (BRFC) - Body ground* Rear RH seat belt buckle switch signal Rear RH seat belt fastened 10 kΩ or higher
Rear RH seat belt unfastened Below 1 Ω
A16-18 (BLFC) - Body ground* Rear LH seat belt buckle switch signal Rear LH seat belt fastened 10 kΩ or higher
Rear LH seat belt unfastened Below 1 Ω
A16-28 (BCFC) - Body ground* Rear center seat belt buckle switch signal Rear center seat belt fastened 10 kΩ or higher
Rear center seat belt unfastened Below 1 Ω

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ All Auto Control

A8-1(BATT) - A17-4(E1) Constant power source Ignition switch ON 11 to 14 V
Ignition switch ON (READY) 11 to 15.5 V
A16-7(IG2) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
A17-1(+B1) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
A8-7(+B2) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
A16-8 (BRFC) - Body ground* Rear RH seat belt buckle switch signal Rear RH seat belt fastened 10 kΩ or higher
Rear RH seat belt unfastened Below 1 Ω
A16-18 (BLFC) - Body ground* Rear LH seat belt buckle switch signal Rear LH seat belt fastened 10 kΩ or higher
Rear LH seat belt unfastened Below 1 Ω
A16-28 (BCFC) - Body ground* Rear center seat belt buckle switch signal Rear center seat belt fastened 10 kΩ or higher
Rear center seat belt unfastened Below 1 Ω



CHECK AIRBAG ECU ASSEMBLY (w/ Occupant Classification System)


C370780N74
3.354,0.26 3.844,0.531 0.49,0.271 4.896,0.271 5.385,0.542 0.49,0.271 1.792,0.26 2.281,0.531 0.49,0.271 3.49,0.323 3.802,0.521 0.313,0.198 10 false D10 5.031,0.333 5.344,0.531 0.313,0.198 10 false G64 1.917,0.323 2.229,0.521 0.313,0.198 10 false G43

Terminal No. Terminal Symbol Destination
G43-30 LBE+ Front seat inner belt assembly LH
G43-24 GNDL Front seat inner belt assembly LH


CHECK OCCUPANT DETECTION ECU (w/ Occupant Classification System)


C238368E31
2.625,0.115 3.083,0.313 0.458,0.198 4.292,0.115 4.75,0.313 0.458,0.198 2.708,0.135 3.135,0.354 0.427,0.219 10 false L19 4.406,0.135 4.813,0.406 0.406,0.271 10 false L20

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
L19-1 - L19-5 Front occupant classification sensor LH power supply Ignition switch ON 11 to 14 V
L19-2 - L19-6 Rear occupant classification sensor LH power supply Ignition switch ON 11 to 14 V
L19-3 - L19-5 Front occupant classification sensor LH signal Ignition switch ON Pulse generation
L19-4 - L19-6 Rear occupant classification sensor LH signal Ignition switch ON Pulse generation
L19-5 - L20-10 Front occupant classification sensor LH ground Always Below 1 V
L19-6 - L20-10 Rear occupant classification sensor LH ground Always Below 1 V
L20-6 - L20-10 Power source Ignition switch ON 11 to 14 V
L20-7 - L20-9 Front passenger side buckle switch signal Always Pulse generation
L20-9 - L20-10 Front passenger side buckle switch ground Always Below 1 V
L20-10 - Body ground Ground Always Below 1 V