Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2021.08
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Headlight ECU LH Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headlight ECU LH Communication Stop Mode Communication stop for "Headlight Control" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Headlight ECU sub-assembly LH branch wire or connector

·

Power source circuit of Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly LH ground circuit



WIRING DIAGRAM

C348701E95
0.313,2.115 1.979,2.469 1.667,0.354 10 false No. 9 Global CAN Junction Connector 0.302,1.948 0.698,2.156 0.396,0.208 10 false G121 1.708,1.438 2.104,1.646 0.396,0.208 10 false 11 1.729,0.854 2.125,1.063 0.396,0.208 10 false 5 5.354,0.844 5.75,1.052 0.396,0.208 10 false 24 5.354,1.427 5.75,1.635 0.396,0.208 10 false 23 5.667,0.979 6.063,1.188 0.396,0.208 10 false CANH 5.656,1.563 6.052,1.771 0.396,0.208 10 false CANL 5.354,2.323 5.75,2.531 0.396,0.208 10 false 13 5.667,2.458 6.063,2.667 0.396,0.208 10 false ECUB 5.406,3.156 5.802,3.365 0.396,0.208 10 false 4 5.667,3.292 6.063,3.5 0.396,0.208 10 false IG 5.354,3.969 5.75,4.177 0.396,0.208 10 false 12 5.646,4.135 6.042,4.344 0.396,0.208 10 false GND 5.25,4.76 5.646,4.969 0.396,0.208 10 false A96 3.875,3.135 5.104,3.396 1.229,0.26 10 false R/B-IG1 NO.1 1.802,2.458 3.49,2.927 1.688,0.469 10 false from H-LP LH Relay 2.135,3.271 3.646,3.656 1.51,0.385 10 false from IG1 Relay 5.24,4.938 7.063,5.302 1.823,0.365 10 false Headlight ECU Sub-assembly LH

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT ECU SUB-ASSEMBLY LH BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A96 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A96)Location & Routing

Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

A96-24 (CANH) - A96-23 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A96)Location & Routing

Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

A96-12 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A96)Location & Routing

Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

A96-4 (IG) - Body ground Ignition switch ON 11 to 14 V
A96-13 (ECUB) - Body ground For approximately 15 seconds after the ignition switch is turned to ON or off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)