Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends signals to the ECU depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the cruise control main switch. Then terminal CCS of the ECU receives the voltage according to the switch condition.

WIRING DIAGRAM


E136385E04


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (CRUISE CONTROL MAIN SWITCH)


    E107091E05
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Cruise Control / Data List.

  1. Check the Data List for proper functioning of the cruise control main switch.

    Hybrid Vehicle Control ECU (Cruise Control): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Main SW M-CPU
    Main switch signal (Main CPU)/ON or OFF
    ON: Main switch on
    OFF: Main switch off
    -
    Cancel Switch
    CANCEL switch signal/ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    - (COAST)/SET switch signal/ON or OFF
    ON: - (COAST)/SET switch on
    OFF: - (COAST)/SET switch off
    -
    RES/ACC Switch
    + (ACCEL)/RES switch signal/ON or OFF
    ON: + (ACCEL)/RES switch on
    OFF: + (ACCEL)/RES switch off
    -

    OK:
    When cruise control main switch operation is performed the results will be same as above.



OK
REPLACE HYBRID VEHICLE CONTROL ECU
NG


2.CHECK HYBRID VEHICLE CONTROL ECU


    I102360E01
  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H14-13 (CCS) - Body ground
    Cruise control main switch off
    10 to 14 V
    +/RES
    6.6 to 10.1 V
    -/SET
    4.5 to 7.1 V
    CANCEL
    2.3 to 4.0 V
    Cruise control main switch on
    Below 1 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


3.INSPECT CRUISE CONTROL MAIN SWITCH


    I039293E01
  1. Disconnect the H14 ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H14-13 (CCS) - Body ground
    Neutral
    10 kΩ or higher
    +/RES
    210 to 270 Ω
    -/SET
    560 to 700 Ω
    CANCEL
    1,380 to 1,700 Ω
    Cruise control main switch on
    Below 1 Ω



OK
REPLACE HYBRID VEHICLE CONTROL ECU
NG


4.INSPECT CRUISE CONTROL MAIN SWITCH


    I102362E02
  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 3
    +/RES
    210 to 270 Ω
    -/SET
    560 to 700 Ω
    CANCEL
    1,380 to 1,700 Ω
    Cruise control main switch on
    Below 1 Ω
    Cruise control main switch off
    10 kΩ or higher



NG
REPLACE CRUISE CONTROL MAIN SWITCH
OK


5.REPLACE HYBRID VEHICLE CONTROL ECU
I102363E01
  1. Disconnect the spiral cable connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A-3 - B-1
    Below 1 Ω
    A-4 - B-3



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.INSPECT SPIRAL CABLE

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

  1. Removal (Click here)
  2. Installation (Click here)


    I102364E02
  1. Remove the spiral cable.

  1. Measure the resistance of the cable.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    A-3 - C12-1 (CCS)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    A-4 - C12-2 (ECC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right



NG
REPLACE SPIRAL CABLE
OK


7.CHECK WIRE HARNESS (SPIRAL CABLE - ECU AND BODY GROUND)
I102402E01
  1. Disconnect the C12 cable connector.

  1. Disconnect the H14 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    C12-1 - H14-13 (CCS)
    Below 1 Ω
    C12-2 - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE