Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0450    Evaporative Emission Control System Pressure Sensor Malfunction

DTC    P0451    Evaporative Emission Control System Pressure Sensor Range / Performance

DTC    P0452    Evaporative Emission Control System Pressure Sensor / Switch Low Input

DTC    P0453    Evaporative Emission Control System Pressure Sensor / Switch High Input

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Items
Malfunction Detection Conditions
Trouble Area
Detection Timing
Detection logic
P0450
Canister pressure sensor voltage abnormal fluctuation
EVAP pressure rapidly fluctuates beyond upper and lower malfunction thresholds for 0.5 seconds.
  1. Canister pump module
  2. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  3. Connector/wire harness (canister pump module - ECM)
  4. ECM
  1. EVAP monitoring (power switch OFF)
  2. Power switch ON (IG)
1 trip
P0451
Canister pressure sensor noisy
Sensor output voltage fluctuates frequently in certain time period.
  1. Canister pump module
  2. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  3. ECM
  1. EVAP monitoring (power switch OFF)
  2. Engine running
2 trip
P0451
Canister pressure sensor stuck
Sensor output voltage does not vary in certain time period.
  1. Canister pump module
  2. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  3. ECM
  1. EVAP monitoring (power switch OFF)
2 trip
P0452
Canister pressure sensor voltage low
EVAP pressure less than 42.1 kPa for 0.5 seconds.
  1. Canister pump module
  2. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  3. Connector/wire harness (canister pump module - ECM)
  4. ECM
  1. EVAP monitoring (power switch OFF)
  2. Power switch ON (IG)
1 trip
P0453
Canister pressure sensor voltage high
Sensor pressure more than 123.8 kPa for 0.5 seconds.
  1. Canister pump module
  2. Connector/wire harness (canister pump module - ECM)
  3. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  4. Connector/wire harness (canister pump module - ECM)
  5. ECM
  1. EVAP monitoring (power switch OFF)
  2. Power switch ON (IG)
1 trip

HINT:
The canister pressure sensor is built into the canister pump module.


DESCRIPTION

NOTICE:
In this vehicle's EVAP system, turning ON the vent valve does not seal off the EVAP system. To check for leaks in the EVAP system, disconnect the air inlet vent hose and apply pressure from the atmosphere side of the canister.

While the engine is running, if a predetermined condition (closed loop, etc.) is met, the purge VSV is opened by the ECM and the stored fuel vapors in the canister are purged to the intake manifold. The ECM changes the duty cycle ratio of the purge VSV to control purge flow volume.
The purge flow volume is also determined by the intake manifold pressure. Atmospheric pressure is allowed into the canister through the vent valve to ensure that the purge flow is maintained when the negative pressure (vacuum) is applied to the canister.
  1. Key-off monitor
    This monitor checks for Evaporative Emission (EVAP) system leaks and canister pump module malfunctions. The monitor starts 5 hours* after the power switch is turned OFF. More than 5 hours are required to allow the fuel to cool down to stabilize the Fuel Tank Pressure (FTP), thus making the EVAP system monitor more accurate.
    The leak detection pump creates negative pressure (vacuum) in the EVAP system and the pressure is measured. Finally, the ECM monitors for leaks from the EVAP system and malfunctions in both the canister pump module and purge VSV, based on the EVAP pressure.

    HINT:
    *: If the engine coolant temperature is not below 35°C (95°F) 5 hours after the power switch is turned OFF, the monitor check starts 2 hours later. If it is still not below 35°C (95°F) 7 hours after the power switch is turned OFF, the monitor check starts 2.5 hours later.


A131350E03


A130305E03


A131438E01


A115543E13


Components
Operations
Canister, Trap canister
Contains activated charcoal to absorb EVAP generated in fuel tank.
Cut-off valve
Located in fuel tank. Valve floats and closes when fuel tank is 100% full.
Purge Vacuum Switching Valve (VSV)
Opens or closes line between canister and intake manifold. ECM uses purge VSV to control EVAP purge flow. In order to discharge EVAP absorbed by canister to intake manifold, ECM opens purge VSV. EVAP discharge volume to intake manifold controlled by purge VSV duty cycle ratio (current-carrying time) (open: ON; closed: OFF).
Roll-over valve
Located in fuel tank. Valve closes by its own weight when vehicle overturns to prevent fuel from spilling out.
Soak timer
Built into ECM. To ensure accurate EVAP monitor, measures 5 hours (+-15 min) after power switch OFF. This allows fuel to cool down, stabilizing Fuel Tank Pressure (FTP). When approximately 5 hours elapsed, ECM activates.
Purge flow switching valve
The purge flow switching valve located on the canister is used to detect leakage from the bladder tank into the fuel tank. The valve opens during the bladder tank leak check. Then, the fuel tank's fuel vapor flows to the intake manifold without passing the canister.
Pump module
Consists of (a) to (d) below. Pump module cannot be disassembled.
(a) Vent valve
Vents and closes EVAP system. When ECM turns valve ON, EVAP system is closed. When ECM turns valve OFF, EVAP system is vented. Negative pressure (vacuum) created in EVAP system to check for EVAP leaks by closing purge VSV, turning vent valve ON (closed) and operating leak detection pump.
(b) Canister pressure sensor
Indicates pressure as voltage. ECM supplies regulated 5 V to canister pressure sensor, and uses feedback from sensor to monitor EVAP system pressure.
(c) Leak detection pump
Creates negative pressure (vacuum) in EVAP system for leak check.
(d) Reference orifice
Has opening with 0.02 inch diameter. Vacuum produced through orifice by closing purge VSV, turning vent valve OFF and operating leak detection pump to monitor 0.02 inch leak criterion. 0.02 inch leak criterion indicates small leak of EVAP.

MONITOR DESCRIPTION



  1. A115543E13

    1. DTC P0450: Canister pressure sensor voltage abnormal fluctuation
      If the canister pressure sensor voltage output rapidly fluctuates between less than 0.45 V and more than 4.9 V, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).
    2. DTC P0451: Canister pressure sensor noisy or stuck
      If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as noise from the canister pressure sensor, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC.
      Alternatively, if the sensor voltage output does not change for 10 seconds, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and sets the DTC.
      (Both of the malfunctions are detected by 2 trip detection logic).
    3. DTC P0452: Canister pressure sensor voltage low
      If the canister pressure sensor voltage output is below 0.45 V, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).
    4. DTC P0453: Canister pressure sensor voltage high
      If the canister pressure sensor voltage output is 4.9 V or more, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

MONITOR STRATEGY


Required Sensors/Components
Canister pump module
Frequency of Operation
Continuous
Duration
Within 15 minutes
MIL Operation
Immediate: P0450, P0452, P0453
2 driving cycles: P0451
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0451 (Noise Monitor): 
Monitor runs whenever following DTCs are not present
None
Atmospheric pressure
70 to 110 kPa (525 to 825 mmHg)
[absolute pressure]
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 35°C (40 to 95°F)
EVAP pressure sensor malfunction (P0450, P0452, P0453)
Not detected
Either of following conditions is met
A or B
A. Engine
Running
B. Time after key off
5 hours

P0451 (Stuck Monitor): 
Monitor runs whenever following DTCs are not present
None
Atmospheric pressure
70 to 110 kPa (525 to 825 mmHg)
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 35°C (40 to 95°F)
EVAP pressure sensor malfunction (P0450, P0452, P0453)
Not detected
Time after key off
5.7 or 9.5 hours

P0450, P0452 and P0453: 
Monitor runs whenever following DTCs are not present
None
When either of following condition is met
(a) or (b)
(a) Power switch
ON
(b) Soak timer
ON

TYPICAL MALFUNCTION THRESHOLDS

  1. P0450: Canister pressure sensor chattering

    EVAP pressure
    Less than 42.1 kPa (315.9 mmHg) or more than 123.8 kPa (928.4 mmHg)
  2. P0451: Canister pressure sensor noise

    Frequency that EVAP pressure change is 0.3 kPa or more
    10 times or more than 10 seconds
  3. P0451: Canister pressure sensor stuck

    EVAP pressure change during reference pressure
    Less than 0.65 kPa (4.88 mmHg)
  4. P0452: Canister pressure sensor low voltage

    EVAP pressure
    Less than 42.1 kPa (315.9 mmHg)
  5. P0453: Canister pressure sensor high voltage

    EVAP pressure
    More than 123.8 kPa (928.4 mmHg)

WIRING DIAGRAM


A151912E02


INSPECTION PROCEDURE

NOTICE:
  1. When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.
  1. Do not disassemble the canister pump module.
  1. Techstream is required to conduct the following diagnostic troubleshooting procedure.

1.CONFIRM DTC AND EVAP PRESSURE
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG) and turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the values.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Evap Vapor Press.

  1. Read the EVAP pressure displayed on Techstream.

    Result:

    Display (DTC Output)
    Test Result
    Suspected Trouble Areas
    Proceed to
    P0451
    -
    1. Canister pressure sensor
    A
    P0452
    Less than 45 kPa (388 mmHg)
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Canister pressure sensor
    3. Short in ECM circuit
    B
    P0453
    More than 120 kPa (900 mmHg)
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Canister pressure sensor
    3. Open in ECM circuit
    C



A
Go to step 5

C
Go to step 4
B


2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
A065744E68
  1. Turn the power switch OFF.

  1. Disconnect the E7 ECM connector.

  1. Measure the resistance between the PPMP (E7-30) terminal of the ECM connector and body ground.

    Result:

    Test Results
    Suspected Trouble Areas
    Proceed to
    10 Ω or less
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Short in canister pressure sensor circuit
    A
    10 kΩ or more
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Short in ECM circuit
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)


    A130306
  1. Disconnect the V7 canister pump module connector.

  1. Disconnect the E7 ECM connector.



    A065744E68
  1. Measure the resistance between the PPMP (E7-30) terminal of the ECM connector and body ground.

    Result:

    Test Results
    Suspected Trouble Areas
    Proceed to
    10 kΩ or more
    1. Short in canister pressure sensor circuit
    A
    10 kΩ or less
    1. Short in wire harness/connector (ECM - canister pressure sensor)
    B



B
Go to step 6
A


Go to step 5

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)


    A130306
  1. Disconnect the V7 canister pump module connector.



    A085258E38
  1. Turn the power switch ON (IG).

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    V7-4 (VCC) - Body ground
    4.5 to 5.0 V
    V7-3 (VOUT) - Body ground
    4.5 to 5.0 V

    Standard resistance:
    Tester Connection
    Specified Condition
    V7-2 (SGND) - Body ground
    100 Ω or less


    Result:

    Test Results
    Suspected Trouble Areas
    Proceed to
    Voltage and resistance within standard ranges
    1. Open in canister pressure sensor circuit
    A
    Voltage and resistance outside standard ranges
    1. Open in wire harness/connector (ECM - canister pressure sensor)
    B



B
Go to step 6
A


5.REPLACE CANISTER ASSEMBLY


  1. Replace the canister assembly (Click here).

    NOTICE:
    When replacing the canister, check the canister pump module interior and related pipes for water, fuel or other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.


    A130304E01



NEXT
Go to step 8

6.REPAIR OR REPLACE HARNESS OR CONNECTOR

HINT:
If the exhaust tailpipe has been removed, go to the next step before reinstalling it.



NEXT
Go to step 8

7.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 8

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG) and turn Techstream ON.

  1. Wait for at least 60 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code / Pending.

    HINT:
    If no pending DTC is displayed on Techstream, the repair has been successfully completed.


NEXT

COMPLETED