Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1610/13    Front Airbag Sensor RH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The front airbag sensor RH consists of the diagnostic circuit and the front deceleration sensor.
If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1610/13 is recorded when a malfunction is detected in the front airbag sensor RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1610/13
When one of following conditions is met:
  1. Center airbag sensor receives a line short signal, an open signal, a short to ground signal or a short to B+ signal from the front airbag sensor RH for 2 seconds.
  2. Front airbag sensor RH malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor RH
  4. Center airbag sensor

WIRING DIAGRAM


C123527E25


INSPECTION PROCEDURE

1.CHECK FOR DTC
C130774E02
  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1610/13 is not output.

    HINT:
    DTCs other than DTC B1610/13 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)
C130775E02
  1. Disconnect the connectors from the center airbag sensor and the front airbag sensor RH.

  1. Using a service wire, connect terminals A18-29 (+SR) and A18-27 (-SR) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    F2-2 (+SR) - F2-1 (-SR)
    Below 1 Ω



NG
Go to step 8
OK


4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)
C130776E04
  1. Disconnect the service wire from connector B.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    F2-2 (+SR) - F2-1 (-SR)
    1 MΩ or higher



NG
Go to step 9
OK


5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+)
C130776E05
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    F2-2 (+SR) - Body ground
    Below 1 V
    F2-1 (-SR) - Body ground
    Below 1 V



NG
Go to step 10
OK


6.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND)
C130776E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    F2-2 (+SR) - Body ground
    1 MΩ or higher
    F2-1 (-SR) - Body ground
    1 MΩ or higher



NG
Go to step 11
OK


7.CHECK FRONT AIRBAG SENSOR RH
C130777E01
  1. Connect the connectors to the center airbag sensor.

  1. Interchange the front airbag sensor RH with the front airbag sensor LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1610/13 and B1615/14 are not output.
    A
    DTC B1610/13 is output.
    B
    DTC B1615/14 is output.
    C

    HINT:
    DTCs other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C
REPLACE FRONT AIRBAG SENSOR RH
A

USE SIMULATION METHOD TO CHECK 

8.CHECK ENGINE ROOM MAIN WIRE (OPEN)
C123572E01
  1. Disconnect the service wire from connector B.

  1. Disconnect the instrument panel wire connector from the engine room main wire.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Using a service wire, connect terminals F2-2 (+SR) and F2-1 (-SR) of connector E.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    IJ2-1 (+SR) - IJ2-2 (-SR)
    Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

9.CHECK ENGINE ROOM MAIN WIRE (SHORT)
C130778E01
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    IJ2-1 (+SR) - IJ2-2 (-SR)
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

10.CHECK ENGINE ROOM MAIN WIRE (TO B+)
C130778E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester connection
    Specified condition
    IJ2-1 (+SR) - Body ground
    Below 1 V
    IJ2-2 (-SR) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

11.CHECK ENGINE ROOM MAIN WIRE (TO GROUND)
C130778E01
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester connection
    Specified condition
    IJ2-1 (+SR) - Body ground
    1 MΩ or higher
    IJ2-2 (-SR) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE