Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Seat position airbag sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat inner belt assembly LH
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM


C145376E03


INSPECTION PROCEDURE

1.CHECK DTC


    C145377E01
  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK 

2.CHECK CONNECTION OF CONNECTORS
  1. Turn the power switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.

  1. Check that the connectors are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)


    C145378E02
  1. Using a service wire, connect terminals 1 and 2 of connector "E".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-9 (DSP+) - A17-17 (DSP-)
    Always
    Below 1 Ω



NG
Go to step 11
OK


5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)


    C145379E02
  1. Disconnect the service wire from connector E.

  1. Measure the resistance between the terminals of connector E according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-9 (DSP+) - A17-17 (DSP-)
    Always
    1 MΩ or higher



NG
Go to step 12
OK


6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)


    C145379E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A17-9 (DSP+) - Body ground
    Power switch ON (IG)
    Below 1 V
    A17-17 (DSP-) - Body ground
    Power switch ON (IG)
    Below 1 V



NG
Go to step 13
OK


7.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)


    C145379E02
  1. Turn the power switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-9 (DSP+) - Body ground
    Always
    1 MΩ or higher
    A17-17 (DSP-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 14
OK


8.CHECK SEAT POSITION AIRBAG SENSOR


    C145377E01
  1. Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 9
OK

USE SIMULATION METHOD TO CHECK 

9.REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the power switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


10.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C145377E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END 

11.CHECK FRONT SEAT INNER BELT ASSEMBLY LH (OPEN)


    C145380E02
  1. Disconnect the floor wire connector from the front seat inner belt assembly LH.

    HINT:
    The service wire has already been inserted into connector "E".

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-2 (LSP+) - S17-4 (LSP-)
    Always
    Below 1 Ω



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE FLOOR WIRE 

12.CHECK FRONT SEAT INNER BELT ASSEMBLY LH (SHORT)


    C145381E02
  1. Disconnect the floor wire connector from the front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-2 (LSP+) - S17-4 (LSP-)
    Always
    1 MΩ or higher



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE FLOOR WIRE 

13.CHECK FRONT SEAT INNER BELT ASSEMBLY LH (SHORT TO B+)


    C145381E02
  1. Turn the power switch OFF.

  1. Disconnect the negative(-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the floor wire connector from the front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S17-2 (LSP+) - Body ground
    Power switch ON (IG)
    Below 1 V
    S17-4 (LSP-) - Body ground
    Power switch ON (IG)
    Below 1 V



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE FLOOR WIRE 

14.CHECK FRONT SEAT INNER BELT ASSEMBLY LH (SHORT TO GROUND)


    C145381E02
  1. Turn the power switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the floor wire connector from the front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    S17-4 (LSP-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE FLOOR WIRE