Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1660/43    Passenger Airbag ON / OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON / OFF indicator circuit consists of the center airbag sensor and the front passenger seat belt warning light.
This circuit indicates the operation condition of the front passenger airbag, front passenger side airbag and passenger side seat belt pretensioner.
DTC B1660/43 is set when a malfunction is detected in the passenger airbag ON / OFF indicator circuit.

DTC No.
DTC Detection Conditions
Trouble Areas
B1660/43
When one of following is met:
  1. Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal from passenger airbag ON / OFF indicator circuit for 2 seconds
  2. Front passenger seat belt warning light malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Front passenger airbag ON / OFF Indicator light
  3. Center airbag sensor

WIRING DIAGRAM


C130799E01


INSPECTION PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the power switch ON (IG).



  1. Check the passenger airbag ON / OFF indicator operation.


    H043700E19


    Result 
    ON / OFF Indicator Illumination
    Proceed to
    Always ON
    A
    OFF
    B



B
Go to step 8
A


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front passenger seat belt warning light.

    OK:
    Connectors are connected.



NG
CONNECT CONNECTOR
OK


3.CHECK FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT
C130800
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Check the passenger airbag ON / OFF indicator operation.

    OK:
    Neither ON nor OFF passenger airbag ON / OFF indicator comes on.



OK
Go to step 14
NG


4.CHECK INSTRUMENT PANEL WIRE (OPEN)
C130801E02
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front passenger seat belt warning light.

  1. Using a service wire, connect terminals F11-1 (PAON) and F11-5 (P-AB) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A18-17 (P-AB) - A18-23 (PAON)
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


5.CHECK INSTRUMENT PANEL WIRE (SHORT)
C130802E01
  1. Disconnect the service wire from connector C.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A18-17 (P-AB) - A18-23 (PAON)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK INSTRUMENT PANEL WIRE (TO B+)
C130802E01
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Terminal Connection
    Specified Condition
    A18-23 (PAON) - Body ground
    Below 1 V
    A18-17 (P-AB) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7.CHECK INSTRUMENT PANEL WIRE (TO GROUND)
C130802E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A18-17 (P-AB) -Body ground
    1 MΩ or higher
    A18-23 (PAON) -Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT 

8.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front passenger seat belt warning light.

    OK:
    Connectors are connected.



NG
CONNECT CONNECTOR
OK


9.CHECK INSTRUMENT PANEL WIRE (OPEN)
C130801E02
  1. Disconnect the connector from the center airbag sensor and the front passenger seat belt warning light.

  1. Using a service wire, connect terminals F11-1 (PAON) and F11-5 (P-AB) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A18-23 (PAON) - A18-17 (P-AB)
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


10.CHECK INSTRUMENT PANEL WIRE (SHORT)
C130802E01
  1. Disconnect the service wire from connector C.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A18-17 (P-AB) - A18-23 (PAON)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


11.CHECK INSTRUMENT PANEL WIRE (TO B+)
C130802E01
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Terminal Connection
    Specified Condition
    A18-23 (PAON) - Body ground
    Below 1 V
    A18-17 (P-AB) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


12.CHECK INSTRUMENT PANEL WIRE (TO GROUND)
C130802E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A18-17 (P-AB) - Body ground
    1 MΩ or higher
    A18-23 (PAON) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


13.CHECK WIRE HARNESS (POWER SOURCE)
C130803E02
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Terminal Connection
    Specified Condition
    F11-6 (IG+) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE POWER SOURCE CIRCUIT
OK


14.CHECK FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT
C130804E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals F11-5 (P-AB) and F11-4 (PBEW) of the front passenger seat belt warning light.

  1. Using a service wire, connect terminals F11-1 (PAON) and F11-4 (PBEW) of the front passenger seat belt warning light.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Check the front passenger airbag ON / OFF indicator operation.

    OK:
    Front passenger airbag ON / OFF indicator comes on



NG
REPLACE FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT
OK


15.CHECK CENTER AIRBAG SENSOR ASSEMBLY
C130805E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor and the front passenger seat belt warning light.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    DTCs other than DTC B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK