Home › ENGINE › 1NZ-FXE COOLING › THERMOSTAT

THERMOSTAT > INSTALLATION

for Preparation Click here



1. INSTALL THERMOSTAT


    A088873E01
  1. Install a new gasket to the thermostat.



    A081900E03
  1. Install the thermostat with the jiggle valve facing upward.

    HINT:
    The jiggle valve may be set within 10° of either side as shown in the illustration.



2. INSTALL WATER INLET


    A086915E01
  1. Install the water inlet to the cylinder block with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    Ensure that the gasket is not stuck between the water inlet and cylinder block.



3. ADD ENGINE COOLANT (for Engine)
  1. Tighten the drain cock plug of the coolant heat storage tank, then disconnect the vinyl hose.

  1. Tighten the drain cock plug of the engine, then disconnect the vinyl hose.

    Torque:
    13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }

  1. Tighten the drain cock plug of the radiator, then disconnect the vinyl hose.



    A092991E01
  1. Connect a vinyl hose to the bleeder plug of the radiator assembly and the radiator reservoir.

    HINT:
    Insert the vinyl hose inside the radiator reservoir tank.



    A088678E01
  1. Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.

  1. Fill the radiator with coolant up to the fill port.

    Standard capacity:
    8.6 liters (9.1 US qts, 7.6 Imp. qts)

    HINT:
    1. When filling coolant, press the radiator hose a few times. If the coolant level goes down, add more coolant.
    2. Amount of coolant to fill: Approximately 2.4 liters (2.5 US qts, 2.1 Imp. qts)
    3. Use of improper coolants may damage the engine cooling system.
    4. Only use "Toyota Super Long Life Coolant", or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.
    5. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene-glycol concentration is approximately 50% and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.
    6. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add more coolant.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

  1. Install the radiator cop.

  1. Fill the radiator reservoir tank with coolant to the full level.

  1. Connect the coolant heat storage water pump connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Select the item:
    Powertrain / Engine and ECT / Data List/Activate the Water Pump

    NOTICE:
    1. The water pump motor operates for 30 seconds after WATER PUMP is ON in the ACTIVE TEST mode, then it automatically stops operating.
    2. Do not actuate the water pump motor without coolant filled.



    A088678E01
  1. Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.

  1. Remove the radiator cap, then fill the radiator with coolant up to the fill port.

    HINT:
    When filling coolant, press the radiator hose a few times. If the coolant level goes down, add more coolant.

  1. Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

  1. Install the radiator cap.

  1. Slowly pour coolant into the radiator reservoir until it reaches the full line.

  1. Disconnect the vinyl hose between the bleeder plug of the radiator assembly and the radiator reservoir tank.

  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine until the thermostat is open.

  1. Stop the engine, then wait until the coolant becomes cold. Remove the radiator cap and check the coolant level.

    CAUTION:
    If the engine or radiator is hot, do not remove the radiator cap.

    If the coolant level is lower, add coolant again. Warm up the engine, then check the coolant level.

  1. When the coolant level stops going down, add coolant to the radiator reservoir tank up to the full level.



4. INSPECT FOR COOLANT LEAK (for Engine)
  1. Fill the radiator with engine coolant and attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi) and check for leakage.



5. INSTALL ENGINE UNDER COVER RH


6. INSTALL ENGINE UNDER COVER LH


7. INSTALL RADIATOR SUPPORT OPENING COVER


    A088174E01
  1. Install the opening cover with the 6 clips.