Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1655/37    Driver Side Seat Belt Buckle Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

The driver side seat belt buckle switch circuit consists of the center airbag sensor and the front seat inner belt LH.
DTC B1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1655/37
When one of following conditions is met:
  1. Center airbag sensor receives a line short signal, an open signal, a short to ground signal or a short to B+ signal from the driver side seat belt buckle switch sensor for 2 seconds.
  2. Front seat inner belt LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat inner belt LH (Driver side seat belt buckle switch)
  3. Center airbag sensor

WIRING DIAGRAM


C123590E02


INSPECTION PROCEDURE

1.CHECK FOR DTC
C130797E01
  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front seat inner belt LH.

    OK:
    Connectors are connected.



NG
CONNECT CONNECTOR
OK


3.CHECK FLOOR WIRE (OPEN)
C130798E01
  1. Disconnect the connectors from the center airbag sensor and the front seat inner belt LH.

  1. Using a service wire, connect terminals A17-10 (DBE+) and A17-18 (DBE-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    S17-1 - S17-3
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT)
C130796E02
  1. Disconnect the service wire from connector B.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    S17-1 - S17-3
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (TO B+)
C130796E02
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester connection
    Specified condition
    S17-1 - Body ground
    Below 1 V
    S17-3 - Body ground
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (TO GROUND)
C130796E02
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester connection
    Specified condition
    S17-1 - Body ground
    1 MΩ or higher
    S17-3 - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
C130797E01
  1. Connect the connectors to the center airbag sensor and the front seat inner belt LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt LH (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


9.CHECK CENTER AIRBAG SENSOR ASSEMBLY
C130797E01
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK