Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0102    Mass or Volume Air Flow Circuit Low Input

DTC    P0103    Mass or Volume Air Flow Circuit High Input

for Preparation Click here


DESCRIPTION

The MAF (Mass Air Flow) meter measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and provides a proper air-fuel ratio. Inside the MAF meter, there is a heated platinum wire exposed to the flow of intake air.
By applying a specific current to the wire, the ECM heats this wire to a given temperature. The flow of incoming air cools the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the air flowing through the sensor. The ECM interprets this voltage as the intake air amount.
The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potential of A and B remains equal to maintain the set temperature.

A080089E02


DTC No.
DTC Detection Condition
Trouble Area
P0102
When the mass air flow meter circuit has an open for more than 3 seconds
  1. Open in mass air flow meter circuit
  2. Mass air flow meter
  3. ECM
P0103
When the mass air flow meter circuit has a short for more than 3 seconds
  1. Short in mass air flow meter circuit
  2. Mass air flow meter
  3. ECM

HINT:
After confirming DTC P0100, P0102 or P0103, confirm the mass air flow ratio in Powertrain / Engine and ECT / Data List / All Data / MAF.

Air Flow Rate (g/sec.)
Malfunction
Approximately 0.0
  1. Mass air flow meter power source circuit open
  2. VG circuit open or shorted
271.0 or more
  1. E2G circuit open


MONITOR DESCRIPTION

If there is a defect in the sensor or an open or short circuit, the voltage level will deviate from the normal operating range. The ECM interprets this deviation as a defect in the MAF meter and sets a DTC.
Example:
When the sensor voltage output is less than 0.2 V or more than 4.9 V and if either condition continues for more than 3 seconds.

MONITOR STRATEGY


Related DTCs
P0100: Mass air flow meter circuit range check (fluttering)
P0102: Mass air flow meter circuit range check (low voltage)
P0103: Mass air flow meter circuit range check (high voltage)
Required sensors/components
Mass air flow meter
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
Immediately (when engine speed is less than 4,000 rpm)
2 driving cycles (when engine speed is 4,000 rpm or more)
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
None

TYPICAL MALFUNCTION THRESHOLDS


P0102: 
Mass air flow meter voltage
Less than 0.2 V

P0103: 
Mass air flow meter voltage
More than 4.9 V

COMPONENT OPERATING RANGE


Mass air flow meter voltage
0.2 to 4.9 V

WIRING DIAGRAM


A151886E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE OF TECHSTREAM (MASS AIR FLOW RATE)
  1. Connect Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

  1. Read its value using Techstream.

    Result:
    Air Flow Rate (g/sec.)
    Proceed to
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0 (*)
    C

    HINT:
    *: The value must be changed when the throttle valve is opened or closed.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.INSPECT MASS AIR FLOW METER (POWER SOURCE)
  1. Turn the power switch ON (IG).



    A180638E01
  1. Disconnect the M1 mass air flow meter connector.

  1. Measure the voltage between the terminal of the wire harness side connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    M1-1 (+B) - Body ground
    9 to 14 V

  1. Reconnect the mass air flow meter connector.



NG
Go to step 5
OK


3.CHECK ECM (VG VOLTAGE)


    A124045E01
  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Measure the voltage between the specified terminals of the E5 ECM connector.

    HINT:
    The A/C switch should be turned OFF.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E5-33 (VG) - E5-32 (EVG)
    Engine is idling
    0.5 to 3.0 V



OK
REPLACE ECM
NG


4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A180638E03
  1. Disconnect the M1 mass air flow meter connector.



    A065745E33
  1. Disconnect the E5 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M1-3 (VG) - E5-33 (VG)
    Below 1 Ω
    M1-2 (E2G) - E5-32 (EVG)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M1-3 (VG) or E5-33 (VG) - Body ground
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER 

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - EFI M RELAY)


    A082810E01
  1. Remove the integration relay from the engine room relay block.



    A054396E56
  1. Disconnect the M1 mass air flow meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M1-1 (+B) - 3I-8 (EFI M relay)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M1-1 (+B) or 3I-8 (EFI M relay) - Body ground
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT 

6.CHECK ECM (SENSOR GROUND)


    A124045E02
  1. Measure the resistance between the specified terminal of the E5 ECM connector and body ground.

    Standard resistance:
    Tester Connection
    Specified Condition
    E5-32 (EVG) - Body ground
    Below 1 Ω



NG
REPLACE ECM
OK


7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A054396E57
  1. Disconnect the M1 mass air flow meter connector.



    A065745E33
  1. Disconnect the E5 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M1-3 (VG) - E5-33 (VG)
    Below 1 Ω
    M1-2 (E2G) - E5-32 (EVG)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M1-3 (VG) or E5-33 (VG) - Body ground
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER