Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

for Preparation Click here


DESCRIPTION

The crankshaft position sensor (CKP) system consists of a crankshaft position sensor plate and a pick-up coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pick-up coil is made of an iron core and magnet. The sensor plate rotates and as each tooth passes through the pick-up coil, a pulse signal is created. The pick-up coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
No crankshaft position sensor signal to ECM
(2 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Signal plate (crankshaft)
  4. ECM
Reference: Inspection using an oscilloscope.
A083873E02

HINT:
The correct waveform is as shown.
Item
Contents
Terminal
CH1: G2 - NE-
CH2: NE+ - NE-
Equipment Setting
5 V/DIV., 20 ms/DIV.
Condition
During cranking or idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft sensor even though the engine is running, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check or rationality
Required sensors/components
Crankshaft position sensor
Frequency of operation
Continuous
Duration
4.7 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
None
Power switch
ON
Engine rotating signal from HV ECU
HV ECU judges that the engine is running

TYPICAL MALFUNCTION THRESHOLDS


Engine speed signal
No signal for 4.7 seconds

WIRING DIAGRAM


A151892E01


INSPECTION PROCEDURE

HINT:
  1. Perform troubleshooting for DTC P0335 first. If no trouble is found, troubleshoot the engine mechanical systems.
  2. Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  3. Read the values using Techstream.
    1. Connect Techstream to the DLC3.
    2. Turn the power switch ON (IG).
    3. Turn Techstream ON.
    4. Put the engine in inspection mode (Click here).
    5. Start the engine.
    6. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
    7. Read the value.
  4. The engine speed can be observed in Data List using Techstream. If there is no NE signal from the crankshaft position sensor even though the engine is running, the engine speed will be indicated as zero. If voltage output from the crankshaft position sensor is insufficient, the engine speed will be indicated as lower PRM (than the actual RPM).

1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)


    A078431E12
  1. Disconnect the C7 crankshaft position sensor connector.

  1. Measure the resistance between the terminals of the crankshaft position sensor connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    985 to 1,600 Ω at cold
    1 - 2
    1,265 to 1,890 Ω at hot

    NOTICE:
    Terms "cold" and "hot" refer to the temperature of the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)


    A075251E04
  1. Disconnect the C7 crankshaft position sensor connector.



    A065743E78
  1. Disconnect the E4 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    C7-1 (NE+) - E4-33 (NE+)
    Below 1 Ω
    C7-2 (NE-) - E4-34 (NE-)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    C7-1 (NE+) or E4-33 (NE+) - Body ground
    10 kΩ or higher
    C7-2 (NE-) or E4-34 (NE-) - Body ground
    10 kΩ or higher

  1. Reconnect the crankshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check that the crankshaft position sensor is properly installed.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


4.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE [CRANKSHAFT])
  1. Check the teeth of the sensor plate.

    OK:
    No deformation on the teeth of the sensor plate.



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE
OK

REPLACE ECM